Blame |
Last modification |
View Log
| RSS feed
unit ST_function;
interface
uses Windows, SysUtils{, Dialogs};
const
ErrNotLoadDLL=32768;
type
TUSMC_Devices = packed record
NOD: DWORD;
Serial: Pointer; //array of PChar;
Version: Pointer; //array of PChar;
end; {USMC_Devices}
TUSMC_Parameters =record
AccelT : Single; // 'Acceleration time (in ms)
DecelT : Single; // 'Deceleration time (in ms)
PTimeout : Single; //'Time (in ms) after which current will be reduced to 60% of normal
BTimeout1 : Single; //'Time (in ms) after which speed of step motor rotation will be equal to the one specified at
// 'BTO1P field (see below). (This parameter is used when controlling step motor using buttons)
BTimeout2 : Single; //'
BTimeout3 : Single; // '
BTimeout4 : Single; // '
BTimeoutR : Single; // 'Time (in ms) after which reset command will be performed
BTimeoutD : Single; // 'This field is reserved for future use
MinP : Single ; // 'Speed (steps/sec) while performing reset operation. (This parameter is used when controlling
// 'step motor using buttons)
BTO1P : Single; // 'Speed (steps/sec) after BTIMEOUT 1 time have p:sed. (This parameter is used when controlling
// 'step motor using buttons)
BTO2P : Single; // '
BTO3P : Single ; // '
BTO4P : Single ; // '
MaxLoft : WORD; // 'Value in full steps that will be used performing backl:h operation
StartPos : DWORD; // 'This field is reserved for future use
RTDelta : WORD; // 'Revolution distance number of full steps per one full revolution
RTMinError : WORD; // 'Number of full steps missed to raise the error flag
MaxTemp : Single; // 'Maximum allowed temperature (Celsius)
SynOUTP : Byte; // 'Duration of the output synchronization pulse
LoftPeriod : Single; // 'Speed of the last phase of the backlash operation.
EncMult: Single; // Encoder step multiplier. Should be <Encoder Steps per Revolution>
// / <SM Steps per Revolution> and should be integer multiplied by 0.25
Reserved: array [1..16] of Byte; // <Unused> File padding
end; {USMC_Parameters}
TUSMC_StartParameters = record
SDivisor: byte; //'Step is divided by this factor (1,2,4,8)
DefDir: LongBool; // 'Direction for backlash operation (relative)
LoftEn: LongBool; // 'Enable automatic backlash operation (works if slow start/stop mode is off)
SlStart: LongBool; // 'If TRUE slow start/stop mode enabled.
WSyncIN: LongBool; // 'If TRUE controller will wait for input synchronization signal to start
SyncOUTR: LongBool; // 'If TRUE output synchronization counter will be reset
ForceLoft: LongBool; // 'If TRUE and destination position is equal to the current position backlash operation will be performed.
Reserved: array [1..4] of Byte; // <Unused> File padding
end; {USMC_StartParameters}
TUSMC_Mode = record
PMode : LongBool; // 'Turn off buttons (TRUE - buttons disabled)
PReg : LongBool; // 'Current reduction regime (TRUE - regime is on)
ResetD : LongBool; // 'Turn power off and make a whole step (TRUE - apply)
EmReset : LongBool; // 'Quick power off
Tr1T : LongBool; // 'Trailer 1 TRUE state (TRUE : +3/+5?; FALSE : 0?)
Tr2T : LongBool; // 'Trailer 2 TRUE state (TRUE : +3/+5?; FALSE : 0?)
RotTrT : LongBool; // 'Rotary Transducer TRUE state (TRUE : +3/+5?; FALSE : 0?)
TrSwap : LongBool; // 'If TRUE, Trailers are treated to be swapped
Tr1En : LongBool; // 'If TRUE Trailer 1 Operation Enabled
Tr2En : LongBool; // 'If TRUE Trailer 2 Operation Enabled
RotTeEn : LongBool; // 'If TRUE Rotary Transducer Operation Enabled
RotTrOp : LongBool; // 'Rotary Transducer Operation Select (stop on error for TRUE)
Butt1T : LongBool; // 'Button 1 TRUE state (TRUE : +3/+5?; FALSE : 0?)
Butt2T : LongBool; // 'Button 2 TRUE state (TRUE : +3/+5?; FALSE : 0?)
ResetRT : LongBool; // 'Reset Rotary Transducer Check Positions (need one full revolution before it can detect error)
SyncOUTEn : LongBool; // 'If TRUE output syncronization enabled
SyncOUTR : LongBool; // 'If TRUE output synchronization counter will be reset
SyncINOp : LongBool; // 'Synchronization input mode:
//'True - Step motor will move one time to the destination position
//'False - Step motor will move multiple times by steps equal to the value destination position
SyncCount : DWORD; // 'Number of steps after which synchronization output sygnal occures
SyncInvert : LongBool; // 'Set to TRUE to invert output synchronization signal
EncoderEn : LongBool; // Enable Encoder on pins {SYNCIN,ROTTR} - disables Synchronization input and Rotary Transducer
EncoderInv : LongBool; // Invert Encoder Counter Direction
ResBEnc : LongBool; // Reset <EncoderPos> and <ECurPos> to 0
ResEnc : LongBool; // Reset <ECurPos> to <EncoderPos>
Reserved: array [1..8] of Byte; // <Unused> File padding
end; {USMC_Mode}
TUSMC_State = record
CurPos: integer; // 'Current position (in microsteps)
Temp: single; // 'Current temperature of the driver
SDivisor: byte; // 'Step is divided by this factor
Loft: LongBool; // 'Indicates backlash status
FullPower: LongBool; // 'If TRUE then full power.
CW_CCW: LongBool; // 'Current direction. Relatively!
Power: LongBool; // 'If TRUE then Step Motor is ON.
FullSpeed: LongBool; // 'If TRUE then full speed. Valid in "Slow Start" mode only.
AReset: LongBool; // 'TRUE After Device reset, FALSE after "Set Position".
RUN: LongBool; // 'Indicates if step motor is rotating
SyncIN: LongBool; // 'Logical state directly from input synchronization PIN
SyncOUT: LongBool; // 'Logical state directly from output synchronization PIN
RotTr: LongBool; // 'Indicates current rotary transducer press state
RotTrErr: LongBool; // 'Indicates rotary transducer error flag
EmReset: LongBool; // 'Indicates state of emergency disable button (local control)
Trailer1: LongBool; // 'Indicates trailer 1 logical state.
Trailer2: LongBool; // 'Indicates trailer 2 logical state.
Voltage: Single; // 'Input power source voltage (6-39V) -=24 version 0nly=-
Reserved: array [1..8] of Byte; // <Unused> File padding
end; {USMC_State}
TUSMC_EncoderState = record
EncoderPos : integer; // Current position measured by encoder
ECurPos : integer; // Current position (in Encoder Steps) - Synchronized with request call
Reserved: array [1..8] of Byte; // <Unused> File padding
end; {USMC_EncoderState}
D_USMC_Init = function (out USMC_Devices: TUSMC_Devices) : Longword; cdecl;
D_USMC_GetState = function (Device: Longword; // IN - Device number
out Str: TUSMC_State // OUT - Structure representing divice state
) : Longword ; cdecl;
D_USMC_SaveParametersToFlash = function (Device: Longword // IN - Device number
) : Longword ; cdecl;
D_USMC_GetMode = function ( Device: Longword; // IN - Device number
out Str: TUSMC_Mode // OUT - Structure representing some of divice parameters
): Longword ; cdecl;
D_USMC_SetMode= function ( Device: Longword; // IN - Device number
var Str: TUSMC_Mode // IN/OUT Structure representing some of divice parameters
): Longword ; cdecl;
D_USMC_GetParameters = function ( Device: Longword; // IN - Device number
out Str: TUSMC_Parameters // OUT - Structure representing some of divice parameters
) : Longword ; cdecl;
D_USMC_SetParameters = function ( Device: Longword; // IN - Device number
var Str: TUSMC_Parameters // IN/OUT Structure representing some of divice parameters
): Longword ; cdecl;
D_USMC_GetStartParameters = function ( Device: Longword; // IN - Device number
out Str: TUSMC_StartParameters // OUT - Structure representing start function parameters
) : Longword ; cdecl;
D_USMC_Start = function ( Device: Longword; // IN - Device number
DestPos: integer; // IN - Destination position
var Speed: single; // IN/OUT - Speed of rotation
out Str: TUSMC_StartParameters // IN/OUT - Structure representing start function parameters
) : Longword ; cdecl;
D_USMC_Stop = function ( Device: Longword // IN - Device number
) : Longword ; cdecl;
D_USMC_SetCurrentPosition = function ( Device: Longword; // IN - Device number
Position: integer // IN - New current position in 1/8 steps (5 least significant bits are ignored)
) : Longword ; cdecl;
D_USMC_GetEncoderState = function ( Device: Longword; // IN - Device number
var Str: TUSMC_EncoderState //IN/OUT Structure containing encoder state
) : Longword ; cdecl;
D_USMC_GetLastErr = procedure (ErrString: PChar; Size: Integer) cdecl;
D_USMC_Close = function : Longword ; cdecl;
TStandaClass = class(TObject)
protected
HandleStandaDLL: THandle;
public
bDllLoadOK: Boolean;
USMC_Init: D_USMC_Init;
USMC_GetState: D_USMC_GetState;
USMC_SaveParametersToFlash: D_USMC_SaveParametersToFlash;
USMC_GetMode: D_USMC_GetMode;
USMC_SetMode: D_USMC_SetMode;
USMC_GetParameters: D_USMC_GetParameters;
USMC_SetParameters: D_USMC_SetParameters;
USMC_GetStartParameters: D_USMC_GetStartParameters;
USMC_Start: D_USMC_Start;
USMC_Stop: D_USMC_Stop;
USMC_SetCurrentPosition: D_USMC_SetCurrentPosition;
USMC_GetEncoderState: D_USMC_GetEncoderState;
USMC_GetLastErr: D_USMC_GetLastErr;
USMC_Close: D_USMC_Close;
function LoadLibAndFuncs : Integer;
function UnLoadLibAndFuncs : Integer;
constructor Create;
destructor Destroy; override;
end;
(******************************************************************************)
implementation
constructor TStandaClass.Create;
var
iError: Integer;
begin
inherited Create;
iError := LoadLibAndFuncs;
if iError <> 0 then
begin
bDllLoadOK := false;
if iError=ErrNotLoadDLL then //ShowMessage('TStandaClass.Create: Error "can`t Load DLL" ')
else ;//ShowMessage('TStandaClass.Create: Error ''' + IntToStr(iError) + ''' from "LoadLibAndFuncs"');
end else
begin
bDllLoadOK := true;
end;
end;
destructor TStandaClass.Destroy;
var
iError: Integer;
begin
iError := UnLoadLibAndFuncs;
if iError <> 0 then
begin
// ShowMessage('TStandaClass.Destroy: Error from "UnLoadLibAndFuncs"');
end;
inherited Destroy;
end;
function TStandaClass.LoadLibAndFuncs : Integer;
begin
Result := 0;
try
HandleStandaDLL := LoadLibrary(pChar('USMCDLL.dll'));
if HandleStandaDLL <> 0 then
begin
@USMC_Init := GetProcAddress(HandleStandaDLL, 'USMC_Init');
@USMC_GetLastErr := GetProcAddress(HandleStandaDLL, 'USMC_GetLastErr');
@USMC_GetState := GetProcAddress(HandleStandaDLL, 'USMC_GetState');
@USMC_GetStartParameters := GetProcAddress(HandleStandaDLL, 'USMC_GetStartParameters');
@USMC_Start := GetProcAddress(HandleStandaDLL, 'USMC_Start');
@USMC_Stop := GetProcAddress(HandleStandaDLL, 'USMC_Stop');
@USMC_GetParameters := GetProcAddress(HandleStandaDLL, 'USMC_GetParameters');
@USMC_SetParameters := GetProcAddress(HandleStandaDLL, 'USMC_SetParameters');
@USMC_GetMode := GetProcAddress(HandleStandaDLL, 'USMC_GetMode');
@USMC_SetMode := GetProcAddress(HandleStandaDLL, 'USMC_SetMode');
@USMC_SaveParametersToFlash := GetProcAddress(HandleStandaDLL, 'USMC_SaveParametersToFlash');
@USMC_SetCurrentPosition := GetProcAddress(HandleStandaDLL, 'USMC_SetCurrentPosition');
@USMC_GetEncoderState := GetProcAddress(HandleStandaDLL, 'USMC_GetEncoderState');
@USMC_Close := GetProcAddress(HandleStandaDLL, 'USMC_Close');
if @USMC_Init = nil then Result := Result + 1;
if @USMC_GetLastErr = nil then Result := Result + 2;
if @USMC_GetState = nil then Result := Result + 4;
if @USMC_GetStartParameters = nil then Result := Result + 8;
if @USMC_Start = nil then Result := Result + 16;
if @USMC_Stop = nil then Result := Result + 32;
if @USMC_GetParameters = nil then Result := Result + 64;
if @USMC_SetParameters = nil then Result := Result + 128;
if @USMC_GetMode = nil then Result := Result + 256;
if @USMC_SetMode = nil then Result := Result + 512;
if @USMC_SaveParametersToFlash = nil then Result := Result + 1024;
if @USMC_SetCurrentPosition = nil then Result := Result + 2048;
if @USMC_GetEncoderState = nil then Result := Result + 4096;
if @USMC_Close = nil then Result := Result + 8192;
end else
begin
Result := ErrNotLoadDLL;
end;
except
on EExternalException do
Result := Result + 100000;
else
Result := Result + 200000; { unexpected }
end;
end; {LoadLibAndFuncs}
function TStandaClass.UnLoadLibAndFuncs : Integer;
var
bOK : Boolean;
begin
Result := 0;
if HandleStandaDLL <> 0 then
begin
bOK := FreeLibrary(HandleStandaDLL);
if bOK = true then
begin
HandleStandaDLL := 0;
USMC_Init := nil;
USMC_GetLastErr := nil;
USMC_GetState := nil;
USMC_GetStartParameters := nil;
USMC_Start := nil;
USMC_Stop := nil;
USMC_GetParameters := nil;
USMC_SetParameters := nil;
USMC_GetMode := nil;
USMC_SetMode := nil;
@USMC_SaveParametersToFlash := nil;
@USMC_SetCurrentPosition := nil;
@USMC_GetEncoderState := nil;
@USMC_Close := nil;
end else
begin
// further: exact info by 'GetLastError()'
Result := 1;
end; {if bOK = true then}
end; {if HandleStandaDLL <> 0 then}
end; {UnLoadLibAndFuncs}
end.