Blame | Last modification | View Log | RSS feed
----------------------------------------------------------------------------------------------------
-- $HeadURL: http://svn.wiener-d.com/src/enet/trunk/mibs/WIENER-CRATE-MIB.txt $
-- $LastChangedDate: 2012-10-04 10:04:09 +0200 (Do, 04. Okt 2012) $
-- $LastChangedRevision: 1959 $
-- $LastChangedBy: koester (roemer)$
-- Copyright © 2005-2007 W-IE-NE-R Plein & Baus GmbH, Burscheid, Germany
----------------------------------------------------------------------------------------------------
WIENER-CRATE-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, OBJECT-IDENTITY,
IpAddress, Integer32, Opaque, enterprises
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, DisplayString
FROM SNMPv2-TC
-- Float
-- FROM NET-SNMP-TC
-- Float
-- FROM UCD-SNMP-MIB
;
wiener MODULE-IDENTITY
LAST-UPDATED "200810090000Z" -- October 9, 2008
ORGANIZATION "WIENER Plein & Baus GmbH"
CONTACT-INFO "
postal: WIENER Plein & Baus GmbH
Mullersbaum 20
D-51399 Burscheid
Germany
email: info@wiener-d.com
"
DESCRIPTION
"Introduction of the communication.can branch.
"
REVISION "200805060000Z" -- May 6, 2008
DESCRIPTION
"Introduction of the signal branch.
"
REVISION "200804150000Z" -- April 15, 2008
DESCRIPTION
"Enlargement of u0..u11 -> u0..u1999
"
REVISION "200804100000Z" -- April 10, 2008
DESCRIPTION
"This revision uses again Integer32 instead of Counter32.
"
REVISION "200804020000Z" -- April 02, 2008
DESCRIPTION
"This revision modifies the syntax of this file to be complient with smilint.
"
REVISION "200709100000Z"
DESCRIPTION
"This revision introduces new OIDs for debug functionality:
sysDebugMemory8, sysDebugMemory16 and sysDebugMemory32.
"
REVISION "200703160000Z"
DESCRIPTION
"This revision introduces new OIDs for slew control:
outputVoltageRiseRate and outputVoltageFallRate.
"
REVISION "200502010000Z"
DESCRIPTION
"This revision introduces new OIDs for group managment:
groupTable
"
REVISION "200406280000Z"
DESCRIPTION
"WIENER Crate MIB, actual Firmware: UEL6E 4.02.
Initial Version.
"
::= { enterprises 19947 }
-------------------------------------------------------------------------------
-- Define the Float Textual Convention
-- This definition was written by David Perkins.
--
Float ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A single precision floating-point number. The semantics
and encoding are identical for type 'single' defined in
IEEE Standard for Binary Floating-Point,
ANSI/IEEE Std 754-1985.
The value is restricted to the BER serialization of
the following ASN.1 type:
FLOATTYPE ::= [120] IMPLICIT FloatType
(note: the value 120 is the sum of '30'h and '48'h)
The BER serialization of the length for values of
this type must use the definite length, short
encoding form.
For example, the BER serialization of value 123
of type FLOATTYPE is '9f780442f60000'h. (The tag
is '9f78'h; the length is '04'h; and the value is
'42f60000'h.) The BER serialization of value
'9f780442f60000'h of data type Opaque is
'44079f780442f60000'h. (The tag is '44'h; the length
is '07'h; and the value is '9f780442f60000'h."
SYNTAX Opaque (SIZE (7))
-------------------------------------------------------------------------------
-- crate
-------------------------------------------------------------------------------
crate OBJECT-IDENTITY
STATUS current
DESCRIPTION
"SNMP control for electronic crates. A crate is a complete electronic system and
consists of the mechanical rack, a power supply, a fan tray and a backplane.
All this things are necessary to provide an adequate housing for electronic
modules (e.g. VME CPU's)"
::= { wiener 1 }
--Crate ::= SEQUENCE {
-- system System,
-- input Input,
-- output Output,
-- sensor Sensor,
-- communication Communication,
-- powersupply Powersupply,
-- fantray Fantray,
-- rack Rack
--}
system OBJECT-IDENTITY
STATUS current
DESCRIPTION
"A collection of objects which affect the complete crate"
::= { crate 1 }
input OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are associated with the power input of the crate"
::= { crate 2 }
output OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are associated with the power output of the crate"
::= { crate 3 }
sensor OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are associated with temperature sensors in the crate"
::= { crate 4 }
communication OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which affect the remote control of the crate"
::= { crate 5 }
powersupply OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are specific for the power supply of the crate"
::= { crate 6 }
fantray OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are specific for the fan tray of the crate"
::= { crate 7 }
rack OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are specific for the crate (BIN) of the crate"
::= { crate 8 }
signal OBJECT-IDENTITY
STATUS current
DESCRIPTION
"All objects which are associated with analog/digtal input/output in the crate"
::= { crate 9 }
-------------------------------------------------------------------------------
-- system
-------------------------------------------------------------------------------
System ::= SEQUENCE {
sysMainSwitch INTEGER,
sysHardwareReset INTEGER,
sysStatus BITS,
sysVmeSysReset INTEGER,
sysConfigDoMeasurementCurrent BITS,
sysOperatingTime Integer32,
sysDebugMemory8 Integer32,
sysDebugMemory16 Integer32,
sysDebugMemory32 Integer32,
sysDebug OCTET STRING,
sysDebugDisplay OCTET STRING,
sysConfig OCTET STRING
}
sysMainSwitch OBJECT-TYPE
SYNTAX INTEGER { off (0), on (1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Read: An enumerated value which shows the current state of
the crates main switch.
Write: Try to switch the complete crate ON or OFF.
Only the values ON or OFF are allowed."
::= { system 1 }
sysStatus OBJECT-TYPE
SYNTAX BITS {
mainOn (0) ,
mainInhibit (1) ,
localControlOnly (2) ,
inputFailure (3) ,
outputFailure (4) ,
fantrayFailure (5) ,
sensorFailure (6),
vmeSysfail (7),
plugAndPlayIncompatible (8),
busReset (9),
supplyDerating (10),
supplyFailure (11),
supplyDerating2 (12),
supplyFailure2 (13)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A bit string which shows the status (health) of the complete crate.
If a bit is set (1), the explanation is satisfied
mainOn (0), system is switched on, individual outputs may be controlled by their specific ON/INHIBIT
mainInhibit(1), external (hardware-)inhibit of the complete system
localControlOnly (2), local control only (CANBUS write access denied)
inputFailure (3), any input failure (e.g. power fail)
outputFailure (4), any output failure, details in outputTable
fantrayFailure (5), fantray failure
sensorFailure (6), temperature of the external sensors too high
vmeSysfail(7), VME SYSFAIL signal is active
plugAndPlayIncompatible (8) wrong power supply and rack connected
busReset (9) The sytem bus (e.g. VME or CPCI) reset signal is active.
supplyDerating (10) The (first) system power supply has the DEG signal active.
supplyFailure (11) The (first) system power supply has the FAL signal active.
supplyDerating2 (12) The second system power supply has the DEG signal active.
supplyFailure2 (13) The second system power supply has the FAL signal active.
"
::= { system 2 }
-- ERROR_BIN_CHECKSUM(?),
sysVmeSysReset OBJECT-TYPE
SYNTAX INTEGER { trigger (1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Read: Always 0.
Write: Trigger the generation of the VME SYSRESET or CPIC RESET signal.
This signal will be active for a time of 200 ms"
::= { system 3 }
sysHardwareReset OBJECT-TYPE
SYNTAX INTEGER --{ off (0), on (1) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Triggered a Reset via Watchdog or ResetLine."
::= { system 4 }
sysConfigDoMeasurementCurrent OBJECT-TYPE
SYNTAX BITS {
ch0 (0) ,
ch1 (1) ,
ch2 (2) ,
ch3 (3) ,
ch4 (4) ,
ch5 (5) ,
ch6 (6) ,
ch7 (7)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"CSet the analog inputs to measure voltage or current."
::= { system 10 }
sysOperatingTime OBJECT-TYPE
SYNTAX Integer32
UNITS "s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The time in seconds for how long the controller was in action."
::= { system 11 }
sysDebugMemory8 OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Debug 16-bit memory access."
::= { system 1024 }
sysDebugMemory16 OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Debug 16-bit memory access."
::= { system 1025 }
sysDebugMemory32 OBJECT-TYPE
SYNTAX Integer32 (-2147483648..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Debug 32-bit memory access."
::= { system 1026 }
sysDebug OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (520))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Debug communication with the MPOD.
This is a direct map to the ancient functions which are accessible
via USB (without SLIP/SNMP).
"
::= { system 1027 }
sysDebugDisplay OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Debug communication with the MPOD display."
::= { system 1028 }
sysConfig OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..25))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Debug config memory access."
::= { system 1029 }
-------------------------------------------------------------------------------
-- input
-------------------------------------------------------------------------------
-- reserved, possible entries:
-- inputSetPfcVoltage
-- inputMesPowerFail
-- inputMesVoltage
-- inputMesCurrent
-- inputMesPower
-- inputMesTemperature
-------------------------------------------------------------------------------
-- output
-------------------------------------------------------------------------------
--Output ::= SEQUENCE {
-- outputNumber Integer32,
-- outputTable OutputTable,
-- groupsNumber Integer32,
-- groupsTable GroupsTable
-- moduleNumber Integer32,
-- moduleTable moduleTable
-- ??TotalPower
--}
outputNumber OBJECT-TYPE
SYNTAX Integer32 (0..1999)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of output channels of the crate."
::= { output 1 }
outputTable OBJECT-TYPE
SYNTAX SEQUENCE OF OutputEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of output entries."
::= { output 2 }
groupsNumber OBJECT-TYPE
SYNTAX Integer32 (1..1999)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of output groups of the crate."
::= { output 3 }
groupsTable OBJECT-TYPE
SYNTAX SEQUENCE OF GroupsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of output groups entries."
::= { output 4 }
-------------------------------------------------------------------------------
-- outputModuleTable
-------------------------------------------------------------------------------
moduleNumber OBJECT-TYPE
SYNTAX Integer32 (1..10)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of HV/LV modules of the crate."
::= { output 5 }
moduleTable OBJECT-TYPE
SYNTAX SEQUENCE OF moduleEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of output module entries."
::= { output 6 }
-------------------------------------------------------------------------------
-- outputTable
-------------------------------------------------------------------------------
outputEntry OBJECT-TYPE
SYNTAX OutputEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table row"
INDEX { outputIndex }
::= { outputTable 1 }
OutputEntry ::= SEQUENCE {
outputIndex INTEGER,
outputName DisplayString,
outputGroup INTEGER,
outputStatus BITS,
outputMeasurementSenseVoltage Float,
outputMeasurementTerminalVoltage Float,
outputMeasurementCurrent Float,
outputMeasurementTemperature INTEGER,
outputSwitch INTEGER,
outputVoltage Float,
outputAdjustVoltage Integer32,
outputCurrent Float,
outputVoltageRiseRate Float,
outputVoltageFallRate Float,
outputSupervisionBehavior Integer32,
outputSupervisionMinSenseVoltage Float,
outputSupervisionMaxSenseVoltage Float,
outputSupervisionMaxTerminalVoltage Float,
outputSupervisionMaxCurrent Float,
outputSupervisionMaxTemperature Integer32,
outputConfigMaxSenseVoltage Float,
outputConfigMaxTerminalVoltage Float,
outputConfigMaxCurrent Float,
outputSupervisionMaxPower Float,
outputConfigGainSenseVoltage Float,
outputConfigOffsetSenseVoltage Float,
outputConfigGainTerminalVoltage Float,
outputConfigOffsetTerminalVoltage Float,
outputConfigGainCurrent Float,
outputConfigOffsetCurrent Float,
outputCurrentRiseRate Float,
outputCurrentFallRate Float,
outputTripTimeMaxCurrent INTEGER,
outputHardwareLimitVoltage Float,
outputHardwareLimitCurrent Float,
outputRegulationMode INTEGER,
outputConfigMaxTemperature Integer32
}
outputIndex OBJECT-TYPE
SYNTAX INTEGER {
u0(1),u1(2),u2(3),u3(4),u4(5),u5(6),u6(7),u7(8),u8(9),u9(10),
u10(11),u11(12),u12(13),u13(14),u14(15),u15(16),u16(17),u17(18),u18(19),u19(20),
u20(21),u21(22),u22(23),u23(24),u24(25),u25(26),u26(27),u27(28),u28(29),u29(30),
u30(31),u31(32),u32(33),u33(34),u34(35),u35(36),u36(37),u37(38),u38(39),u39(40),
u40(41),u41(42),u42(43),u43(44),u44(45),u45(46),u46(47),u47(48),u48(49),u49(50),
u50(51),u51(52),u52(53),u53(54),u54(55),u55(56),u56(57),u57(58),u58(59),u59(60),
u60(61),u61(62),u62(63),u63(64),u64(65),u65(66),u66(67),u67(68),u68(69),u69(70),
u70(71),u71(72),u72(73),u73(74),u74(75),u75(76),u76(77),u77(78),u78(79),u79(80),
u80(81),u81(82),u82(83),u83(84),u84(85),u85(86),u86(87),u87(88),u88(89),u89(90),
u90(91),u91(92),u92(93),u93(94),u94(95),u95(96),u96(97),u97(98),u98(99),u99(100),
u100(101),u101(102),u102(103),u103(104),u104(105),u105(106),u106(107),u107(108),u108(109),u109(110),
u110(111),u111(112),u112(113),u113(114),u114(115),u115(116),u116(117),u117(118),u118(119),u119(120),
u120(121),u121(122),u122(123),u123(124),u124(125),u125(126),u126(127),u127(128),u128(129),u129(130),
u130(131),u131(132),u132(133),u133(134),u134(135),u135(136),u136(137),u137(138),u138(139),u139(140),
u140(141),u141(142),u142(143),u143(144),u144(145),u145(146),u146(147),u147(148),u148(149),u149(150),
u150(151),u151(152),u152(153),u153(154),u154(155),u155(156),u156(157),u157(158),u158(159),u159(160),
u160(161),u161(162),u162(163),u163(164),u164(165),u165(166),u166(167),u167(168),u168(169),u169(170),
u170(171),u171(172),u172(173),u173(174),u174(175),u175(176),u176(177),u177(178),u178(179),u179(180),
u180(181),u181(182),u182(183),u183(184),u184(185),u185(186),u186(187),u187(188),u188(189),u189(190),
u190(191),u191(192),u192(193),u193(194),u194(195),u195(196),u196(197),u197(198),u198(199),u199(200),
u200(201),u201(202),u202(203),u203(204),u204(205),u205(206),u206(207),u207(208),u208(209),u209(210),
u210(211),u211(212),u212(213),u213(214),u214(215),u215(216),u216(217),u217(218),u218(219),u219(220),
u220(221),u221(222),u222(223),u223(224),u224(225),u225(226),u226(227),u227(228),u228(229),u229(230),
u230(231),u231(232),u232(233),u233(234),u234(235),u235(236),u236(237),u237(238),u238(239),u239(240),
u240(241),u241(242),u242(243),u243(244),u244(245),u245(246),u246(247),u247(248),u248(249),u249(250),
u250(251),u251(252),u252(253),u253(254),u254(255),u255(256),u256(257),u257(258),u258(259),u259(260),
u260(261),u261(262),u262(263),u263(264),u264(265),u265(266),u266(267),u267(268),u268(269),u269(270),
u270(271),u271(272),u272(273),u273(274),u274(275),u275(276),u276(277),u277(278),u278(279),u279(280),
u280(281),u281(282),u282(283),u283(284),u284(285),u285(286),u286(287),u287(288),u288(289),u289(290),
u290(291),u291(292),u292(293),u293(294),u294(295),u295(296),u296(297),u297(298),u298(299),u299(300),
u300(301),u301(302),u302(303),u303(304),u304(305),u305(306),u306(307),u307(308),u308(309),u309(310),
u310(311),u311(312),u312(313),u313(314),u314(315),u315(316),u316(317),u317(318),u318(319),u319(320),
u320(321),u321(322),u322(323),u323(324),u324(325),u325(326),u326(327),u327(328),u328(329),u329(330),
u330(331),u331(332),u332(333),u333(334),u334(335),u335(336),u336(337),u337(338),u338(339),u339(340),
u340(341),u341(342),u342(343),u343(344),u344(345),u345(346),u346(347),u347(348),u348(349),u349(350),
u350(351),u351(352),u352(353),u353(354),u354(355),u355(356),u356(357),u357(358),u358(359),u359(360),
u360(361),u361(362),u362(363),u363(364),u364(365),u365(366),u366(367),u367(368),u368(369),u369(370),
u370(371),u371(372),u372(373),u373(374),u374(375),u375(376),u376(377),u377(378),u378(379),u379(380),
u380(381),u381(382),u382(383),u383(384),u384(385),u385(386),u386(387),u387(388),u388(389),u389(390),
u390(391),u391(392),u392(393),u393(394),u394(395),u395(396),u396(397),u397(398),u398(399),u399(400),
u400(401),u401(402),u402(403),u403(404),u404(405),u405(406),u406(407),u407(408),u408(409),u409(410),
u410(411),u411(412),u412(413),u413(414),u414(415),u415(416),u416(417),u417(418),u418(419),u419(420),
u420(421),u421(422),u422(423),u423(424),u424(425),u425(426),u426(427),u427(428),u428(429),u429(430),
u430(431),u431(432),u432(433),u433(434),u434(435),u435(436),u436(437),u437(438),u438(439),u439(440),
u440(441),u441(442),u442(443),u443(444),u444(445),u445(446),u446(447),u447(448),u448(449),u449(450),
u450(451),u451(452),u452(453),u453(454),u454(455),u455(456),u456(457),u457(458),u458(459),u459(460),
u460(461),u461(462),u462(463),u463(464),u464(465),u465(466),u466(467),u467(468),u468(469),u469(470),
u470(471),u471(472),u472(473),u473(474),u474(475),u475(476),u476(477),u477(478),u478(479),u479(480),
u480(481),u481(482),u482(483),u483(484),u484(485),u485(486),u486(487),u487(488),u488(489),u489(490),
u490(491),u491(492),u492(493),u493(494),u494(495),u495(496),u496(497),u497(498),u498(499),u499(500),
u500(501),u501(502),u502(503),u503(504),u504(505),u505(506),u506(507),u507(508),u508(509),u509(510),
u510(511),u511(512),u512(513),u513(514),u514(515),u515(516),u516(517),u517(518),u518(519),u519(520),
u520(521),u521(522),u522(523),u523(524),u524(525),u525(526),u526(527),u527(528),u528(529),u529(530),
u530(531),u531(532),u532(533),u533(534),u534(535),u535(536),u536(537),u537(538),u538(539),u539(540),
u540(541),u541(542),u542(543),u543(544),u544(545),u545(546),u546(547),u547(548),u548(549),u549(550),
u550(551),u551(552),u552(553),u553(554),u554(555),u555(556),u556(557),u557(558),u558(559),u559(560),
u560(561),u561(562),u562(563),u563(564),u564(565),u565(566),u566(567),u567(568),u568(569),u569(570),
u570(571),u571(572),u572(573),u573(574),u574(575),u575(576),u576(577),u577(578),u578(579),u579(580),
u580(581),u581(582),u582(583),u583(584),u584(585),u585(586),u586(587),u587(588),u588(589),u589(590),
u590(591),u591(592),u592(593),u593(594),u594(595),u595(596),u596(597),u597(598),u598(599),u599(600),
u600(601),u601(602),u602(603),u603(604),u604(605),u605(606),u606(607),u607(608),u608(609),u609(610),
u610(611),u611(612),u612(613),u613(614),u614(615),u615(616),u616(617),u617(618),u618(619),u619(620),
u620(621),u621(622),u622(623),u623(624),u624(625),u625(626),u626(627),u627(628),u628(629),u629(630),
u630(631),u631(632),u632(633),u633(634),u634(635),u635(636),u636(637),u637(638),u638(639),u639(640),
u640(641),u641(642),u642(643),u643(644),u644(645),u645(646),u646(647),u647(648),u648(649),u649(650),
u650(651),u651(652),u652(653),u653(654),u654(655),u655(656),u656(657),u657(658),u658(659),u659(660),
u660(661),u661(662),u662(663),u663(664),u664(665),u665(666),u666(667),u667(668),u668(669),u669(670),
u670(671),u671(672),u672(673),u673(674),u674(675),u675(676),u676(677),u677(678),u678(679),u679(680),
u680(681),u681(682),u682(683),u683(684),u684(685),u685(686),u686(687),u687(688),u688(689),u689(690),
u690(691),u691(692),u692(693),u693(694),u694(695),u695(696),u696(697),u697(698),u698(699),u699(700),
u700(701),u701(702),u702(703),u703(704),u704(705),u705(706),u706(707),u707(708),u708(709),u709(710),
u710(711),u711(712),u712(713),u713(714),u714(715),u715(716),u716(717),u717(718),u718(719),u719(720),
u720(721),u721(722),u722(723),u723(724),u724(725),u725(726),u726(727),u727(728),u728(729),u729(730),
u730(731),u731(732),u732(733),u733(734),u734(735),u735(736),u736(737),u737(738),u738(739),u739(740),
u740(741),u741(742),u742(743),u743(744),u744(745),u745(746),u746(747),u747(748),u748(749),u749(750),
u750(751),u751(752),u752(753),u753(754),u754(755),u755(756),u756(757),u757(758),u758(759),u759(760),
u760(761),u761(762),u762(763),u763(764),u764(765),u765(766),u766(767),u767(768),u768(769),u769(770),
u770(771),u771(772),u772(773),u773(774),u774(775),u775(776),u776(777),u777(778),u778(779),u779(780),
u780(781),u781(782),u782(783),u783(784),u784(785),u785(786),u786(787),u787(788),u788(789),u789(790),
u790(791),u791(792),u792(793),u793(794),u794(795),u795(796),u796(797),u797(798),u798(799),u799(800),
u800(801),u801(802),u802(803),u803(804),u804(805),u805(806),u806(807),u807(808),u808(809),u809(810),
u810(811),u811(812),u812(813),u813(814),u814(815),u815(816),u816(817),u817(818),u818(819),u819(820),
u820(821),u821(822),u822(823),u823(824),u824(825),u825(826),u826(827),u827(828),u828(829),u829(830),
u830(831),u831(832),u832(833),u833(834),u834(835),u835(836),u836(837),u837(838),u838(839),u839(840),
u840(841),u841(842),u842(843),u843(844),u844(845),u845(846),u846(847),u847(848),u848(849),u849(850),
u850(851),u851(852),u852(853),u853(854),u854(855),u855(856),u856(857),u857(858),u858(859),u859(860),
u860(861),u861(862),u862(863),u863(864),u864(865),u865(866),u866(867),u867(868),u868(869),u869(870),
u870(871),u871(872),u872(873),u873(874),u874(875),u875(876),u876(877),u877(878),u878(879),u879(880),
u880(881),u881(882),u882(883),u883(884),u884(885),u885(886),u886(887),u887(888),u888(889),u889(890),
u890(891),u891(892),u892(893),u893(894),u894(895),u895(896),u896(897),u897(898),u898(899),u899(900),
u900(901),u901(902),u902(903),u903(904),u904(905),u905(906),u906(907),u907(908),u908(909),u909(910),
u910(911),u911(912),u912(913),u913(914),u914(915),u915(916),u916(917),u917(918),u918(919),u919(920),
u920(921),u921(922),u922(923),u923(924),u924(925),u925(926),u926(927),u927(928),u928(929),u929(930),
u930(931),u931(932),u932(933),u933(934),u934(935),u935(936),u936(937),u937(938),u938(939),u939(940),
u940(941),u941(942),u942(943),u943(944),u944(945),u945(946),u946(947),u947(948),u948(949),u949(950),
u950(951),u951(952),u952(953),u953(954),u954(955),u955(956),u956(957),u957(958),u958(959),u959(960),
u960(961),u961(962),u962(963),u963(964),u964(965),u965(966),u966(967),u967(968),u968(969),u969(970),
u970(971),u971(972),u972(973),u973(974),u974(975),u975(976),u976(977),u977(978),u978(979),u979(980),
u980(981),u981(982),u982(983),u983(984),u984(985),u985(986),u986(987),u987(988),u988(989),u989(990),
u990(991),u991(992),u992(993),u993(994),u994(995),u995(996),u996(997),u997(998),u998(999),u999(1000),
u1000(1001),u1001(1002),u1002(1003),u1003(1004),u1004(1005),u1005(1006),u1006(1007),u1007(1008),u1008(1009),u1009(1010),
u1010(1011),u1011(1012),u1012(1013),u1013(1014),u1014(1015),u1015(1016),u1016(1017),u1017(1018),u1018(1019),u1019(1020),
u1020(1021),u1021(1022),u1022(1023),u1023(1024),u1024(1025),u1025(1026),u1026(1027),u1027(1028),u1028(1029),u1029(1030),
u1030(1031),u1031(1032),u1032(1033),u1033(1034),u1034(1035),u1035(1036),u1036(1037),u1037(1038),u1038(1039),u1039(1040),
u1040(1041),u1041(1042),u1042(1043),u1043(1044),u1044(1045),u1045(1046),u1046(1047),u1047(1048),u1048(1049),u1049(1050),
u1050(1051),u1051(1052),u1052(1053),u1053(1054),u1054(1055),u1055(1056),u1056(1057),u1057(1058),u1058(1059),u1059(1060),
u1060(1061),u1061(1062),u1062(1063),u1063(1064),u1064(1065),u1065(1066),u1066(1067),u1067(1068),u1068(1069),u1069(1070),
u1070(1071),u1071(1072),u1072(1073),u1073(1074),u1074(1075),u1075(1076),u1076(1077),u1077(1078),u1078(1079),u1079(1080),
u1080(1081),u1081(1082),u1082(1083),u1083(1084),u1084(1085),u1085(1086),u1086(1087),u1087(1088),u1088(1089),u1089(1090),
u1090(1091),u1091(1092),u1092(1093),u1093(1094),u1094(1095),u1095(1096),u1096(1097),u1097(1098),u1098(1099),u1099(1100),
u1100(1101),u1101(1102),u1102(1103),u1103(1104),u1104(1105),u1105(1106),u1106(1107),u1107(1108),u1108(1109),u1109(1110),
u1110(1111),u1111(1112),u1112(1113),u1113(1114),u1114(1115),u1115(1116),u1116(1117),u1117(1118),u1118(1119),u1119(1120),
u1120(1121),u1121(1122),u1122(1123),u1123(1124),u1124(1125),u1125(1126),u1126(1127),u1127(1128),u1128(1129),u1129(1130),
u1130(1131),u1131(1132),u1132(1133),u1133(1134),u1134(1135),u1135(1136),u1136(1137),u1137(1138),u1138(1139),u1139(1140),
u1140(1141),u1141(1142),u1142(1143),u1143(1144),u1144(1145),u1145(1146),u1146(1147),u1147(1148),u1148(1149),u1149(1150),
u1150(1151),u1151(1152),u1152(1153),u1153(1154),u1154(1155),u1155(1156),u1156(1157),u1157(1158),u1158(1159),u1159(1160),
u1160(1161),u1161(1162),u1162(1163),u1163(1164),u1164(1165),u1165(1166),u1166(1167),u1167(1168),u1168(1169),u1169(1170),
u1170(1171),u1171(1172),u1172(1173),u1173(1174),u1174(1175),u1175(1176),u1176(1177),u1177(1178),u1178(1179),u1179(1180),
u1180(1181),u1181(1182),u1182(1183),u1183(1184),u1184(1185),u1185(1186),u1186(1187),u1187(1188),u1188(1189),u1189(1190),
u1190(1191),u1191(1192),u1192(1193),u1193(1194),u1194(1195),u1195(1196),u1196(1197),u1197(1198),u1198(1199),u1199(1200),
u1200(1201),u1201(1202),u1202(1203),u1203(1204),u1204(1205),u1205(1206),u1206(1207),u1207(1208),u1208(1209),u1209(1210),
u1210(1211),u1211(1212),u1212(1213),u1213(1214),u1214(1215),u1215(1216),u1216(1217),u1217(1218),u1218(1219),u1219(1220),
u1220(1221),u1221(1222),u1222(1223),u1223(1224),u1224(1225),u1225(1226),u1226(1227),u1227(1228),u1228(1229),u1229(1230),
u1230(1231),u1231(1232),u1232(1233),u1233(1234),u1234(1235),u1235(1236),u1236(1237),u1237(1238),u1238(1239),u1239(1240),
u1240(1241),u1241(1242),u1242(1243),u1243(1244),u1244(1245),u1245(1246),u1246(1247),u1247(1248),u1248(1249),u1249(1250),
u1250(1251),u1251(1252),u1252(1253),u1253(1254),u1254(1255),u1255(1256),u1256(1257),u1257(1258),u1258(1259),u1259(1260),
u1260(1261),u1261(1262),u1262(1263),u1263(1264),u1264(1265),u1265(1266),u1266(1267),u1267(1268),u1268(1269),u1269(1270),
u1270(1271),u1271(1272),u1272(1273),u1273(1274),u1274(1275),u1275(1276),u1276(1277),u1277(1278),u1278(1279),u1279(1280),
u1280(1281),u1281(1282),u1282(1283),u1283(1284),u1284(1285),u1285(1286),u1286(1287),u1287(1288),u1288(1289),u1289(1290),
u1290(1291),u1291(1292),u1292(1293),u1293(1294),u1294(1295),u1295(1296),u1296(1297),u1297(1298),u1298(1299),u1299(1300),
u1300(1301),u1301(1302),u1302(1303),u1303(1304),u1304(1305),u1305(1306),u1306(1307),u1307(1308),u1308(1309),u1309(1310),
u1310(1311),u1311(1312),u1312(1313),u1313(1314),u1314(1315),u1315(1316),u1316(1317),u1317(1318),u1318(1319),u1319(1320),
u1320(1321),u1321(1322),u1322(1323),u1323(1324),u1324(1325),u1325(1326),u1326(1327),u1327(1328),u1328(1329),u1329(1330),
u1330(1331),u1331(1332),u1332(1333),u1333(1334),u1334(1335),u1335(1336),u1336(1337),u1337(1338),u1338(1339),u1339(1340),
u1340(1341),u1341(1342),u1342(1343),u1343(1344),u1344(1345),u1345(1346),u1346(1347),u1347(1348),u1348(1349),u1349(1350),
u1350(1351),u1351(1352),u1352(1353),u1353(1354),u1354(1355),u1355(1356),u1356(1357),u1357(1358),u1358(1359),u1359(1360),
u1360(1361),u1361(1362),u1362(1363),u1363(1364),u1364(1365),u1365(1366),u1366(1367),u1367(1368),u1368(1369),u1369(1370),
u1370(1371),u1371(1372),u1372(1373),u1373(1374),u1374(1375),u1375(1376),u1376(1377),u1377(1378),u1378(1379),u1379(1380),
u1380(1381),u1381(1382),u1382(1383),u1383(1384),u1384(1385),u1385(1386),u1386(1387),u1387(1388),u1388(1389),u1389(1390),
u1390(1391),u1391(1392),u1392(1393),u1393(1394),u1394(1395),u1395(1396),u1396(1397),u1397(1398),u1398(1399),u1399(1400),
u1400(1401),u1401(1402),u1402(1403),u1403(1404),u1404(1405),u1405(1406),u1406(1407),u1407(1408),u1408(1409),u1409(1410),
u1410(1411),u1411(1412),u1412(1413),u1413(1414),u1414(1415),u1415(1416),u1416(1417),u1417(1418),u1418(1419),u1419(1420),
u1420(1421),u1421(1422),u1422(1423),u1423(1424),u1424(1425),u1425(1426),u1426(1427),u1427(1428),u1428(1429),u1429(1430),
u1430(1431),u1431(1432),u1432(1433),u1433(1434),u1434(1435),u1435(1436),u1436(1437),u1437(1438),u1438(1439),u1439(1440),
u1440(1441),u1441(1442),u1442(1443),u1443(1444),u1444(1445),u1445(1446),u1446(1447),u1447(1448),u1448(1449),u1449(1450),
u1450(1451),u1451(1452),u1452(1453),u1453(1454),u1454(1455),u1455(1456),u1456(1457),u1457(1458),u1458(1459),u1459(1460),
u1460(1461),u1461(1462),u1462(1463),u1463(1464),u1464(1465),u1465(1466),u1466(1467),u1467(1468),u1468(1469),u1469(1470),
u1470(1471),u1471(1472),u1472(1473),u1473(1474),u1474(1475),u1475(1476),u1476(1477),u1477(1478),u1478(1479),u1479(1480),
u1480(1481),u1481(1482),u1482(1483),u1483(1484),u1484(1485),u1485(1486),u1486(1487),u1487(1488),u1488(1489),u1489(1490),
u1490(1491),u1491(1492),u1492(1493),u1493(1494),u1494(1495),u1495(1496),u1496(1497),u1497(1498),u1498(1499),u1499(1500),
u1500(1501),u1501(1502),u1502(1503),u1503(1504),u1504(1505),u1505(1506),u1506(1507),u1507(1508),u1508(1509),u1509(1510),
u1510(1511),u1511(1512),u1512(1513),u1513(1514),u1514(1515),u1515(1516),u1516(1517),u1517(1518),u1518(1519),u1519(1520),
u1520(1521),u1521(1522),u1522(1523),u1523(1524),u1524(1525),u1525(1526),u1526(1527),u1527(1528),u1528(1529),u1529(1530),
u1530(1531),u1531(1532),u1532(1533),u1533(1534),u1534(1535),u1535(1536),u1536(1537),u1537(1538),u1538(1539),u1539(1540),
u1540(1541),u1541(1542),u1542(1543),u1543(1544),u1544(1545),u1545(1546),u1546(1547),u1547(1548),u1548(1549),u1549(1550),
u1550(1551),u1551(1552),u1552(1553),u1553(1554),u1554(1555),u1555(1556),u1556(1557),u1557(1558),u1558(1559),u1559(1560),
u1560(1561),u1561(1562),u1562(1563),u1563(1564),u1564(1565),u1565(1566),u1566(1567),u1567(1568),u1568(1569),u1569(1570),
u1570(1571),u1571(1572),u1572(1573),u1573(1574),u1574(1575),u1575(1576),u1576(1577),u1577(1578),u1578(1579),u1579(1580),
u1580(1581),u1581(1582),u1582(1583),u1583(1584),u1584(1585),u1585(1586),u1586(1587),u1587(1588),u1588(1589),u1589(1590),
u1590(1591),u1591(1592),u1592(1593),u1593(1594),u1594(1595),u1595(1596),u1596(1597),u1597(1598),u1598(1599),u1599(1600),
u1600(1601),u1601(1602),u1602(1603),u1603(1604),u1604(1605),u1605(1606),u1606(1607),u1607(1608),u1608(1609),u1609(1610),
u1610(1611),u1611(1612),u1612(1613),u1613(1614),u1614(1615),u1615(1616),u1616(1617),u1617(1618),u1618(1619),u1619(1620),
u1620(1621),u1621(1622),u1622(1623),u1623(1624),u1624(1625),u1625(1626),u1626(1627),u1627(1628),u1628(1629),u1629(1630),
u1630(1631),u1631(1632),u1632(1633),u1633(1634),u1634(1635),u1635(1636),u1636(1637),u1637(1638),u1638(1639),u1639(1640),
u1640(1641),u1641(1642),u1642(1643),u1643(1644),u1644(1645),u1645(1646),u1646(1647),u1647(1648),u1648(1649),u1649(1650),
u1650(1651),u1651(1652),u1652(1653),u1653(1654),u1654(1655),u1655(1656),u1656(1657),u1657(1658),u1658(1659),u1659(1660),
u1660(1661),u1661(1662),u1662(1663),u1663(1664),u1664(1665),u1665(1666),u1666(1667),u1667(1668),u1668(1669),u1669(1670),
u1670(1671),u1671(1672),u1672(1673),u1673(1674),u1674(1675),u1675(1676),u1676(1677),u1677(1678),u1678(1679),u1679(1680),
u1680(1681),u1681(1682),u1682(1683),u1683(1684),u1684(1685),u1685(1686),u1686(1687),u1687(1688),u1688(1689),u1689(1690),
u1690(1691),u1691(1692),u1692(1693),u1693(1694),u1694(1695),u1695(1696),u1696(1697),u1697(1698),u1698(1699),u1699(1700),
u1700(1701),u1701(1702),u1702(1703),u1703(1704),u1704(1705),u1705(1706),u1706(1707),u1707(1708),u1708(1709),u1709(1710),
u1710(1711),u1711(1712),u1712(1713),u1713(1714),u1714(1715),u1715(1716),u1716(1717),u1717(1718),u1718(1719),u1719(1720),
u1720(1721),u1721(1722),u1722(1723),u1723(1724),u1724(1725),u1725(1726),u1726(1727),u1727(1728),u1728(1729),u1729(1730),
u1730(1731),u1731(1732),u1732(1733),u1733(1734),u1734(1735),u1735(1736),u1736(1737),u1737(1738),u1738(1739),u1739(1740),
u1740(1741),u1741(1742),u1742(1743),u1743(1744),u1744(1745),u1745(1746),u1746(1747),u1747(1748),u1748(1749),u1749(1750),
u1750(1751),u1751(1752),u1752(1753),u1753(1754),u1754(1755),u1755(1756),u1756(1757),u1757(1758),u1758(1759),u1759(1760),
u1760(1761),u1761(1762),u1762(1763),u1763(1764),u1764(1765),u1765(1766),u1766(1767),u1767(1768),u1768(1769),u1769(1770),
u1770(1771),u1771(1772),u1772(1773),u1773(1774),u1774(1775),u1775(1776),u1776(1777),u1777(1778),u1778(1779),u1779(1780),
u1780(1781),u1781(1782),u1782(1783),u1783(1784),u1784(1785),u1785(1786),u1786(1787),u1787(1788),u1788(1789),u1789(1790),
u1790(1791),u1791(1792),u1792(1793),u1793(1794),u1794(1795),u1795(1796),u1796(1797),u1797(1798),u1798(1799),u1799(1800),
u1800(1801),u1801(1802),u1802(1803),u1803(1804),u1804(1805),u1805(1806),u1806(1807),u1807(1808),u1808(1809),u1809(1810),
u1810(1811),u1811(1812),u1812(1813),u1813(1814),u1814(1815),u1815(1816),u1816(1817),u1817(1818),u1818(1819),u1819(1820),
u1820(1821),u1821(1822),u1822(1823),u1823(1824),u1824(1825),u1825(1826),u1826(1827),u1827(1828),u1828(1829),u1829(1830),
u1830(1831),u1831(1832),u1832(1833),u1833(1834),u1834(1835),u1835(1836),u1836(1837),u1837(1838),u1838(1839),u1839(1840),
u1840(1841),u1841(1842),u1842(1843),u1843(1844),u1844(1845),u1845(1846),u1846(1847),u1847(1848),u1848(1849),u1849(1850),
u1850(1851),u1851(1852),u1852(1853),u1853(1854),u1854(1855),u1855(1856),u1856(1857),u1857(1858),u1858(1859),u1859(1860),
u1860(1861),u1861(1862),u1862(1863),u1863(1864),u1864(1865),u1865(1866),u1866(1867),u1867(1868),u1868(1869),u1869(1870),
u1870(1871),u1871(1872),u1872(1873),u1873(1874),u1874(1875),u1875(1876),u1876(1877),u1877(1878),u1878(1879),u1879(1880),
u1880(1881),u1881(1882),u1882(1883),u1883(1884),u1884(1885),u1885(1886),u1886(1887),u1887(1888),u1888(1889),u1889(1890),
u1890(1891),u1891(1892),u1892(1893),u1893(1894),u1894(1895),u1895(1896),u1896(1897),u1897(1898),u1898(1899),u1899(1900),
u1900(1901),u1901(1902),u1902(1903),u1903(1904),u1904(1905),u1905(1906),u1906(1907),u1907(1908),u1908(1909),u1909(1910),
u1910(1911),u1911(1912),u1912(1913),u1913(1914),u1914(1915),u1915(1916),u1916(1917),u1917(1918),u1918(1919),u1919(1920),
u1920(1921),u1921(1922),u1922(1923),u1923(1924),u1924(1925),u1925(1926),u1926(1927),u1927(1928),u1928(1929),u1929(1930),
u1930(1931),u1931(1932),u1932(1933),u1933(1934),u1934(1935),u1935(1936),u1936(1937),u1937(1938),u1938(1939),u1939(1940),
u1940(1941),u1941(1942),u1942(1943),u1943(1944),u1944(1945),u1945(1946),u1946(1947),u1947(1948),u1948(1949),u1949(1950),
u1950(1951),u1951(1952),u1952(1953),u1953(1954),u1954(1955),u1955(1956),u1956(1957),u1957(1958),u1958(1959),u1959(1960),
u1960(1961),u1961(1962),u1962(1963),u1963(1964),u1964(1965),u1965(1966),u1966(1967),u1967(1968),u1968(1969),u1969(1970),
u1970(1971),u1971(1972),u1972(1973),u1973(1974),u1974(1975),u1975(1976),u1976(1977),u1977(1978),u1978(1979),u1979(1980),
u1980(1981),u1981(1982),u1982(1983),u1983(1984),u1984(1985),u1985(1986),u1986(1987),u1987(1988),u1988(1989),u1989(1990),
u1990(1991),u1991(1992),u1992(1993),u1993(1994),u1994(1995),u1995(1996),u1996(1997),u1997(1998),u1998(1999),u1999(2000)}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each power output channel. Its value
ranges between 1 and total number of output channels.
This value is equivalent to the output channel number at
the type label of the crate or power supply, but because the SMI
index starts at 1, index 1 corresponds to U0."
::= { outputEntry 1 }
outputName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..10))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A textual string containing a short name of the
output. If the crate is equipped with an alphanumeric
display, this string is shown to identify a output channel."
::= { outputEntry 2 }
outputGroup OBJECT-TYPE
SYNTAX Integer32 (1..63)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The group number (1...63) assigned to each channel.
If commands shall be sent to all channels with a specific group number (e.g.
with the groupsSwitch command defined below), additional bits can be added to
the group number:
HLgggggg
g: Group number (1...63)
L: Mask bit: 1: high voltage channels only, no low voltage channels
H: Mask bit: 1: low voltage channels only, no high voltage channels
Special groups: 0: all (LV+HV) channels
0x40: all, but no LV channels
0x80: all, but no HV channels
"
::= { outputEntry 3 }
outputStatus OBJECT-TYPE
SYNTAX BITS {
outputOn (0) ,
outputInhibit (1) ,
outputFailureMinSenseVoltage (2),
outputFailureMaxSenseVoltage (3),
outputFailureMaxTerminalVoltage (4),
outputFailureMaxCurrent (5),
outputFailureMaxTemperature (6),
outputFailureMaxPower (7),
-- reserved
outputFailureTimeout (9),
outputCurrentLimited (10),
outputRampUp (11),
outputRampDown (12),
outputEnableKill(13),
outputEmergencyOff (14)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A bit string which shows the status (health and operating conditions) of one output channel.
If a bit is set (1), the explanation is satisfied:
outputOn (0), output channel is on
outputInhibit(1), external (hardware-)inhibit of the output channel
outputFailureMinSenseVoltage (2) Supervision limit hurt: Sense voltage is too low
outputFailureMaxSenseVoltage (3), Supervision limit hurt: Sense voltage is too high
outputFailureMaxTerminalVoltage (4), Supervision limit hurt: Terminal voltage is too high
outputFailureMaxCurrent (5), Supervision limit hurt: Current is too high
outputFailureMaxTemperature (6), Supervision limit hurt: Heat sink temperature is too high
outputFailureMaxPower (7), Supervision limit hurt: Output power is too high
outputFailureTimeout (9), Communication timeout between output channel and main control
outputCurrentLimited (10), Current limiting is active (constant current mode)
outputRampUp (11), Output voltage is increasing (e.g. after switch on)
outputRampDown (12), Output voltage is decreasing (e.g. after switch off)
outputEnableKill (13), EnableKill is aktive
outputEmergencyOff (14), EmergencyOff event is aktive
"
::= { outputEntry 4 }
outputMeasurementSenseVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured voltage at the sense input lines."
::= { outputEntry 5 }
outputMeasurementTerminalVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured voltage at the output terminals."
::= { outputEntry 6 }
outputMeasurementCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured output current."
::= { outputEntry 7 }
outputMeasurementTemperature OBJECT-TYPE
SYNTAX INTEGER { ok (-128), failure(127) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured temperature of the power module."
::= { outputEntry 8 }
outputSwitch OBJECT-TYPE
SYNTAX INTEGER { off (0), on (1), resetEmergencyOff (2), setEmergencyOff (3), clearEvents (10) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Read: An enumerated value which shows the current state of
the output channel.
Write: Change the state of the channel.
If the channel is On, and the write value is Off, then the channel
will switch Off.
If the channel is Off, and the write value is On, and if no other
signals (mainInhibit, outputInhibit, outputEmergencyOff or outputFailureMaxCurrent)
are active, then the channel will switch on.
If the write value is resetEmergencyOff, then the channel will
leave the state EmergencyOff. A write of clearEvents is necessary
before the voltage can ramp up again.
If the write value is setEmergencyOff, then the channel will have
the state EmergencyOff, which means that the High Voltage will
switch off without a ramp and reset of the outputVoltage to null volt.
If the write value is clearEvents, then all failure messages
of the outputStatus will be reset (all channel events, all module events
and the state emergencyOff)."
::= { outputEntry 9 }
outputVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The nominal output voltage of the channel."
::= { outputEntry 10 }
outputAdjustVoltage OBJECT-TYPE
SYNTAX Integer32 (-128..127)
MAX-ACCESS read-write
STATUS obsolete
DESCRIPTION
"A posibillity to make small changes of the output voltage."
::= { outputEntry 11 }
outputCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The current limit of the channel."
::= { outputEntry 12 }
outputVoltageRiseRate OBJECT-TYPE
SYNTAX Float
UNITS "V/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Voltage Fall Slew Rate [V/s].
The slew rate of the output voltage if it increases (after switch on or if the Voltage has been
changed).
"
::= { outputEntry 13 }
outputVoltageFallRate OBJECT-TYPE
SYNTAX Float
UNITS "V/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Voltage Rise Slew Rate [V/s].
The slew rate of the output voltage if it decreases (after switch off or if the Voltage has been
changed).
"
::= { outputEntry 14 }
outputSupervisionBehavior OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A bit field packed into an integer which define the behavior of the output channel / power supply
after failures.
For each supervision value, a two-bit field exists.
The enumeration of this value (..L+..H*2) is:
WIENER LV devices
0 ignore the failure
1 switch off this channel
2 switch off all channels with the same group number
3 switch off the complete crate.
iseg HV devices
0 ignore the failure
1 switch off this channel by ramp down the voltage
2 switch off this channel by a emergencyOff
3 switch off the whole board of the HV module by emergencyOff.
The position of the bit fields in the integer value are:
Bit 0, 1: outputFailureMinSenseVoltage
Bit 2, 3: outputFailureMaxSenseVoltage
Bit 4, 5: outputFailureMaxTerminalVoltage
Bit 6, 7: outputFailureMaxCurrent
Bit 8, 9: outputFailureMaxTemperature
Bit 10, 11: outputFailureMaxPower
Bit 12, 13: outputFailureInhibit
Bit 14, 15: outputFailureTimeout
"
::= { outputEntry 15 }
outputSupervisionMinSenseVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured sense voltage is below this value, the power supply
performs the function defined by SupervisionAction."
::= { outputEntry 16 }
outputSupervisionMaxSenseVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured sense voltage is above this value, the power supply
performs the function defined by SupervisionAction."
::= { outputEntry 17 }
outputSupervisionMaxTerminalVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured voltage at the power supply output
terminals is above this value, the power supply
performs the function defined by SupervisionAction."
::= { outputEntry 18 }
outputSupervisionMaxCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured current is above this value, the power supply
performs the function defined by SupervisionAction."
::= { outputEntry 19 }
outputSupervisionMaxTemperature OBJECT-TYPE
-- SYNTAX Integer32 (-128..127)
SYNTAX Integer32
UNITS "deg C"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured module temperature is above this value, the power supply
performs the function defined by SupervisionAction."
::= { outputEntry 20 }
outputConfigMaxSenseVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum possible value of the sense voltage"
::= { outputEntry 21 }
outputConfigMaxTerminalVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum possible value of the terminal voltage"
::= { outputEntry 22 }
outputConfigMaxCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum possible value of the output current"
::= { outputEntry 23 }
outputSupervisionMaxPower OBJECT-TYPE
SYNTAX Float
UNITS "W"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured power (measured current * measured terminal voltage)
is above this value, the power supply performs the function defined
by SupervisionAction."
::= { outputEntry 24 }
outputCurrentRiseRate OBJECT-TYPE
SYNTAX Float
UNITS "A/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Current Fall Slew Rate [A/s].
The slew rate of the output current if it increases (after
switch on or if the Current has been changed).
"
::= { outputEntry 25 }
outputCurrentFallRate OBJECT-TYPE
SYNTAX Float
UNITS "A/s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Current Rise Slew Rate [A/s].
The slew rate of the output current if it decreases (after
switch off or if the Current has been changed).
"
::= { outputEntry 26 }
outputTripTimeMaxCurrent OBJECT-TYPE
SYNTAX INTEGER (0..4000)
UNITS "ms"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Current trip time out [ms].
The outputTripTimeMaxCurrent defines a span for the time out function.
The activity is depending from the bit field outputFailureMaxCurrent
of the outputSupervisionBehavior."
::= { outputEntry 27 }
outputHardwareLimitVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Hardware Voltage Limit [V].
Potentiometer to adjust the global hardware voltage limit (for all
channels of a module).
"
::= { outputEntry 28 }
outputHardwareLimitCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Hardware Current Limit [A].
Potentiometer to adjust the global hardware current limit (for all
channels of a module).
"
::= { outputEntry 29 }
outputConfigGainSenseVoltage OBJECT-TYPE
SYNTAX Float
UNITS ""
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The gain value of the sense voltage"
::= { outputEntry 30 }
outputConfigOffsetSenseVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The offset value of the sense voltage"
::= { outputEntry 31 }
outputConfigGainTerminalVoltage OBJECT-TYPE
SYNTAX Float
UNITS ""
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The gain value of the sense voltage"
::= { outputEntry 32 }
outputConfigOffsetTerminalVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The offset value of the sense voltage"
::= { outputEntry 33 }
outputConfigGainCurrent OBJECT-TYPE
SYNTAX Float
UNITS ""
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The gain value of the sense voltage"
::= { outputEntry 34 }
outputConfigOffsetCurrent OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The offset value of the sense voltage"
::= { outputEntry 35 }
outputUserConfig OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Definition of user-changeable items.
A bit field packed into an integer which define the behavior of the output channel.
Usable for WIENER LV devices only.
The position of the bit fields in the integer value are:
Bit 0: Voltage ramping at switch off:
0: Ramp down at switch off.
1: No ramp at switch off (immediate off)
Bit 1, 2: Set different regulation modes, dependent on the
cable inductance:
0: fast: short cables, up to 1 meter.
1: moderate: cables from 1 to 30 meter.
2: slow: cables longer than 30 meter.
3: slow (identical to 2, should not be used)
Bit 3: Internal sense line connection to the output (MPOD only):
0: The sense input at the sense connector is used
for regulation.
1: The output voltage is used for regulation.
Any signals at the sense connector are ignored.
Bit 4: External Inhibit input.
0: The external inhibit input is ignored.
1: The external inhibit input must be connected to
a voltage source to allow switch on.
Community required for write access: guru.
"
::= { outputEntry 37 }
outputRegulationMode OBJECT-TYPE
SYNTAX INTEGER { fast (0), moderate (1), slow (2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Definition of the regulation mode.
It is possible to set different regulation modes, dependent on the
cable inductance.
fast: short cables, up to 1 meter.
moderate: cables from 1 to 30 meter.
slow: cables longer than 30 meter.
outputUserConfig in the future.
Community required for write access: guru.
"
::= { outputEntry 38 }
outputConfigMaxTemperature OBJECT-TYPE
SYNTAX Integer32
-- SYNTAX Integer32 (-128..127)
UNITS "deg C"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum possible value of outputSupervisionMaxTemperature."
::= { outputEntry 39 }
-------------------------------------------------------------------------------
-- output->groups
-------------------------------------------------------------------------------
groupsEntry OBJECT-TYPE
SYNTAX GroupsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table row"
INDEX { groupsIndex }
::= { groupsTable 1 }
GroupsEntry ::=
SEQUENCE {
groupsIndex
INTEGER,
-- outputGroupsName
-- DisplayString,
-- outputGroupsGroup
-- INTEGER,
-- outputGroupsStatus
-- BITS,
-- outputGroupsMeasurementSenseVoltage
-- Float,
-- outputMeasurementTerminalVoltage
-- Float,
-- outputMeasurementCurrent
-- Float,
-- outputMeasurementTemperature
-- INTEGER,
groupsSwitch
INTEGER
-- outputVoltage
-- Float,
-- outputAdjustVoltage
-- INTEGER,
-- outputCurrent
-- Float,
-- outputRampUp
-- Float,
-- outputRampDown
-- Float,
-- outputSupervisionBehavior
-- INTEGER,
-- outputSupervisionMinSenseVoltage
-- Float,
-- outputSupervisionMaxSenseVoltage
-- Float,
-- outputSupervisionMaxTerminalVoltage
-- Float,
-- outputSupervisionMaxCurrent
-- Float,
-- outputSupervisionMaxTemperature
-- INTEGER,
-- outputConfigMaxSenseVoltage
-- Float,
-- outputConfigMaxTerminalVoltage
-- Float,
-- outputConfigMaxCurrent
-- Float,
-- outputSupervisionMaxPower
-- Float,
}
groupsIndex OBJECT-TYPE
SYNTAX Integer32 (0..1999)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each power output group. Its value
ranges between 1 and 1999.
The special group 0 is predefined and gives access to all channels.
"
::= { groupsEntry 1 }
groupsSwitch OBJECT-TYPE
SYNTAX INTEGER { undefined (-1), off (0), on (1), resetEmergencyOff (2), setEmergencyOff(3), disableKill (4), enableKill (5), clearEvents(10) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Read: This function is not defined with groups of output channels.
Write: Switch the state of all channels of a group.
If any channel is On, and the write value is Off, then all channels
will switch off.
If any channel is Off, and the write value is On, and if no other
signals (mainInhibit, outputInhibit, outputEmergencyOff or outputFailureMaxCurrent)
are active, then all channels will switch on.
If the write value is resetEmergencyOff, then all channels will
leave the state EmergencyOff. A write of clearEvents is necessary
before the voltage can ramp up again.
If the write value is setEmergencyOff, then all channels will have
the state EmergencyOff, which means that the High Voltage will
switch off without a ramp and reset of the outputVoltage to null volt.
If the write value is disableKILL, then all channels will switch
to disableKill (outputStatus outputDisableKill).
If the write value is enableKILL, then all channels will switch
to enableKill (outputStatus outputEnableKill).
If the write value is clearEvents, then all failure messages
of the outputStatus will be cleared (all channel events,
all module events and the state outputEmergencyOff will be reset).
For a detailed description of the different group numbers available
look at the outputGroup OID above.
"
::= { groupsEntry 9 }
--groupsName OBJECT-TYPE
-- SYNTAX DisplayString (SIZE (1..4))
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "A textual string containing a short name of the
-- output. If the crate is equipped with an alphanumeric
-- display, this string is shown to identify a output channel."
-- ::= { groupsEntry 2 }
-------------------------------------------------------------------------------
-- output->module
-------------------------------------------------------------------------------
-- device related parsing of the HV data items
--
-- advantage:
-- Parsing this branch the user directly recognises the structure
-- of HV/LV devices and the hierarchie of data items,
-- module and channel functions and their interaction.
-- This branch gives an image of the module seen from outsite.
-- The inner structure will be transformed into a simple and reduced namspace
-- which has implemented the common module items and the items for the single
-- channels.
-- Module characteristics will image the propeties to a moduleTable which
-- gives an access to the collected properties of the module items whitout
-- a splitting for board 1 and board 2.
-- The channels sequence will collect all the channels also these
-- from a second board if it is integrated.
-------------------------------------------------------------------------------
moduleEntry OBJECT-TYPE
SYNTAX HvdevEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the table of HV/LV modules"
INDEX { moduleIndex }
::= { moduleTable 1 }
moduleEntry ::= SEQUENCE {
moduleIndex INTEGER,
moduleName DisplayString,
moduleDescription OCTET STRING,
moduleSerialNumber INTEGER32,
mduleFirmwareRelease FLOAT,
moduleFirmwareName OCTET STRING,
moduleChannelNumber INTEGER32,
moduleSupply24 FLOAT,
moduleSupply5 FLOAT,
moduleAuxiliaryNumber INTEGER32,
moduleAuxiliaryTable ModuleAuxiliaryTable
}
moduleIndex OBJECT-TYPE
SYNTAX INTEGER {
ma0(1),ma1(2),ma2(3),ma3(4),ma4(5),ma5(6),ma6(7),ma7(8),ma8(9),ma9(10)}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each HV/LV module. Its value
ranges between 1 and the total number of HV/LV modules.
Note, index 1 corresponds to ma0."
::= { moduleEntry 1 }
moduleName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string containing a short name of the
HV/LV module."
::= { moduleEntry 2 }
-- vvvv Folgendes wird später zusammengefasst zu moduleDescription
moduleSerialNumber OBJECT-TYPE
SYNTAX Integer32 (100000..999999)
UNITS ""
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Serial number of the module."
::= { moduleEntry 3 }
moduleFirmwareRelease OBJECT-TYPE
SYNTAX Float
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Firmware release of the module"
::= { moduleEntry 4 }
moduleFirmwareName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Name of the device's firmware:
'E16D0' EDS 16 channels per PCB, distributor module, range of Vmax from VO max to (VO max - 1kV)
'E16D1' EDS 16 channels per PCB, distributor module
'E08C0' EHS 8 channels per PCB, common GND module
'E08F0' EHS 8 channels per PCB, floating GND module
'E08F2' EHS 8 channels per PCB, floating GND module, 2 current measurement ranges
'E08C2' EHS 8 channels per PCB, common floating GND module, 2 current measurement ranges
'E08B0' EBS 8 bipolars channel per PCB, distributor module
'H101C0' HPS 1 channel HV high power supply
"
::= { moduleEntry 5 }
-- ^^^^ Oben wird später zusammengefasst zu moduleDescription
-- vvvv Was ist das?
moduleChannelNumber OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Channel number of the module"
::= { moduleEntry 6 }
-- vvvv Folgendes wird ersetzt
moduleSupply24 OBJECT-TYPE
SYNTAX Float
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Module power supply 24V"
::= { moduleEntry 7 }
moduleSupply5 OBJECT-TYPE
SYNTAX Float
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Module power supply 5V"
::= { moduleEntry 8 }
-- ^^^^ wird ersetzt durch weiter unten
moduleDescription OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..26))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"vendor FirmwareName, SerialNumber, FirmwareRelease"
::= { moduleEntry 9 }
-- vvvv Ersatz für moduleSupply:
-------------------------------------------------------------------------------
moduleAuxiliaryNumber OBJECT-TYPE
SYNTAX Integer32 (0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of auxiliary channels of the power module."
::= { moduleEntry 10 }
moduleAuxiliaryTable OBJECT-TYPE
SYNTAX SEQUENCE OF ModuleAuxiliaryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of ModuleAuxiliary entries."
::= { moduleEntry 11 }
-----------------------------------------------
moduleAuxiliaryEntry OBJECT-TYPE
SYNTAX ModuleAuxiliaryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table row"
INDEX { moduleAuxiliaryIndex }
::= { moduleAuxiliaryTable 1 }
ModuleAuxiliaryEntry ::= SEQUENCE {
moduleAuxiliaryIndex INTEGER,
moduleAuxiliaryMeasurementVoltage Float,
}
moduleAuxiliaryIndex OBJECT-TYPE
SYNTAX INTEGER {
u0(1),u1(2),u2(3),u3(4),u4(5),u5(6),u6(7),u7(8)}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each module auxiliary channel. Its value
ranges between 1 and total number of output channels.
SMI index starts at 1, so index 1 corresponds to U0."
::= { moduleAuxiliaryEntry 1 }
moduleAuxiliaryMeasurementVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured module auxiliary voltage."
::= { moduleAuxiliaryEntry 2 }
-- ^^^^ Ende Ersatz
-------------------------------------------------------------------------------
-- sensor
-------------------------------------------------------------------------------
--Sensor ::= SEQUENCE {
-- sensorNumber Integer32,
-- sensorTable SensorTable
--}
sensorNumber OBJECT-TYPE
SYNTAX Integer32 (0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of temperature sensors of the crate."
::= { sensor 1 }
sensorTable OBJECT-TYPE
SYNTAX SEQUENCE OF SensorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A (conceptual table) of temperature sensor data."
::= { sensor 2 }
sensorEntry OBJECT-TYPE
SYNTAX SensorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) of the sensorTable."
INDEX { sensorIndex }
::= { sensorTable 1 }
SensorEntry ::= SEQUENCE {
sensorIndex INTEGER,
sensorTemperature INTEGER,
-- sensorOkThreshold INTEGER, nicht implementiert (for futur)
sensorWarningThreshold INTEGER,
sensorAlarmThreshold INTEGER,
sensorFailureThreshold INTEGER,
sensorName DisplayString,
sensorID OCTET STRING,
sensorStatus INTEGER
}
sensorIndex OBJECT-TYPE
SYNTAX INTEGER { temp1 (1), temp2(2), temp3(3), temp4(4), temp5(5),
temp6(6), temp7(7), temp8(8) }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each temperature sensor in the crate"
::= { sensorEntry 1 }
sensorTemperature OBJECT-TYPE
-- CHECK SYNTAX INTEGER { UNUSED(-128), (-127..127) }
SYNTAX Integer32 (-128..127)
UNITS "deg C"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured temperature of the sensor.
Unused temperature probes have the special value -128"
::= { sensorEntry 2 }
sensorWarningThreshold OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0..126), DISABLED(127) }
SYNTAX Integer32 (0..127)
UNITS "deg C"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured temperature of the sensor is higher than this
value, the fan speed of the connected fan tray is increased.
The value 127 has the special meaning: channel disabled."
::= { sensorEntry 3}
sensorFailureThreshold OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0..126), DISABLED(127) }
SYNTAX Integer32 (0..127)
UNITS "deg C"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured temperature of the sensor is higher than this
value, the power supply switches off.
The value 127 has the special meaning: channel disabled."
::= { sensorEntry 4}
--sensorOkThreshold OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0..126), DISABLED(127) }
-- SYNTAX Integer32 (0..127)
-- UNITS "deg C"
-- MAX-ACCESS read-write
-- STATUS current
-- DESCRIPTION
-- "If the measured temperature of the sensor is ok,
-- so it is possible to switch of the fans.
-- The value 127 has the special meaning: channel disabled."
-- ::= { sensorEntry 5}
sensorAlarmThreshold OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0..126), DISABLED(127) }
SYNTAX Integer32 (0..127)
UNITS "deg C"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If the measured temperature of the sensor is much higher than this
value, the fans rotate in full speed.
The value 127 has the special meaning: channel disabled."
::= { sensorEntry 6}
sensorName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..7))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A textual string containing a short name of the
sensor. If the crate is equipped with an alphanumeric
display, this string is shown to identify a sensor channel."
::= { sensorEntry 7 }
sensorID OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Shows the 1-Wire Id of the corresponding Sensor."
::= { sensorEntry 8}
sensorStatus OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A bit field packed into an integer which define the Status of the Sensors
after failures. For each Status value, a two-bit field exists.
Bits-Value
00 Temperature is ok
01 Temperature is over WarningThreshold
10 Temperature is over AlarmThreshold
11 Temperature is over FailureThreshold
The position of the bit fields in the integer value are:
Bit 0, 1: Sensor1
Bit 2, 3: Sensor2
Bit 4, 5: Sensor3
Bit 6, 7: Sensor4
Bit 8, 9: Sensor5
Bit 10, 11: Sensor6
Bit 12, 13: Sensor7
Bit 14, 15: Sensor8"
::= { sensorEntry 9}
--################
-------------------------------------------------------------------------------
-- communication
-------------------------------------------------------------------------------
--Communication ::= SEQUENCE {
-- snmp Snmp,
-- tcpip Tcpip,
-- http Http,
-- telnet Telnet,
-- canbus Canbus,
-- rs232 RS232
--}
-------------------------------------------------------------------------------
-- communication.snmp
-------------------------------------------------------------------------------
snmp OBJECT-IDENTITY
STATUS current
DESCRIPTION
"SNMP configuration."
::= { communication 1 }
SnmpCommunityEntry ::= SEQUENCE {
snmpAccessRight INTEGER,
snmpCommunityName OCTET STRING,
snmpCommunityTable SnmpCommunityEntry,
snmpPort INTEGER,
ipDynamicAddress IpAddress,
--OCTET STRING,
ipStaticAddress IpAddress,
--OCTET STRING,
macAddress OCTET STRING
}
snmpCommunityTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnmpCommunityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNMP community string table for different views."
::= { snmp 1 }
snmpCommunityEntry OBJECT-TYPE
SYNTAX SnmpCommunityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One table row."
INDEX { snmpAccessRight }
::= { snmpCommunityTable 1 }
snmpAccessRight OBJECT-TYPE
SYNTAX INTEGER { public (1), private (2), admin (3), guru (4) }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each access right"
::= { snmpCommunityEntry 1 }
snmpCommunityName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SNMP community names for different views. The rights of the different communities are:
public no write access
private can switch power on/off, generate system reset
admin can change supervision levels
guru can change output voltage & current (this may destroy hardware if done wrong!)
Setting a community name to a zero-length string completly
disables the access to this view. If there is no higher-
privileged community, the community name can only changed
by direct access to the crate (not via network)!
"
::= { snmpCommunityEntry 2}
snmpPort OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The UDP port number of the SNMP protocol"
::= { snmp 2}
firmwareUpdate OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..30))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Send a update String"
::= { snmp 10}
ipDynamicAddress OBJECT-TYPE
SYNTAX IpAddress
--OCTET STRING (SIZE (4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Shows the Ip which is currently used"
::= { snmp 11}
ipStaticAddress OBJECT-TYPE
SYNTAX IpAddress
--OCTET STRING (SIZE (4))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Shows the Ip which is setted by user"
::= { snmp 12}
macAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Shows the MAC of the corresponding device"
::= { snmp 13}
-------------------------------------------------------------------------------
-- communication.canTunnel
-------------------------------------------------------------------------------
can OBJECT-IDENTITY
STATUS current
DESCRIPTION
"CAN-Bus tunnel via SNMP."
::= { communication 2 }
canBitRate OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Control of the CAN-Bus.
The value defines the bit rate of the CAN-bus interface.
A write disconnects the CAN interface from the ISEG modules and connects
it to the SNMP communication. Both the receive and transmit fifos are
cleared and the CAN interface is initialized with the selected bit rate.
The special bit rate 0 disables the tunnel and switches back to normal operation.
"
::= { can 1 }
canReceive OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (14))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Control of the CAN-Bus Receive FIFO.
A read access returns the total number of CAN messages stored in the receive
fifo and the oldest message.
This message is removed from the fifo.
The OCTET STRING data is formatted according to the CANviaSNMP structure.
"
::= { can 2 }
canTransmit OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Control of the CAN-Bus Transmit FIFO.
A read access returns the total number of CAN messages stored in the transmit
fifo and a NULL message.
A write inserts the CAN message into the transmit fifo. This message will be
transmitted via the CAN interface later. The total number of CAN messages
stored in the transmit fifo and the recent message are returned.
The OCTET STRING data is formatted according to the CANviaSNMP structure.
"
::= { can 3 }
canReceiveHv OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (14))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Control of the internal HV CAN-Bus on the backplane Receive FIFO.
A read access returns the total number of CAN messages stored in the receive
fifo and the oldest message.
This message is removed from the fifo.
The OCTET STRING data is formatted according to the CANviaSNMP structure.
"
::= { can 4 }
canTransmitHv OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Control of the internal HV CAN-Bus on the backplane.
A write access with:
CANID=0x600 DLC=4 DATAID=0x1001 CONTROL
will switch the HV modules into a special state.
CONTROL=0x0001 - enable SNMP CAN access, stop the refresh cycle for the data points of the name space
CONTROL=0x0002 - disable SNMP CAN access, activate the refresh cycle for the data points of the name space
A write access unequal to CANID=0x600 will be transmitted to the HV CAN on the backplane.
Such a message will be transmitted immediately via the CAN interface.
The OCTET STRING data is formatted according to the CANviaSNMP structure.
"
::= { can 5 }
-------------------------------------------------------------------------------
-- communication....
-------------------------------------------------------------------------------
-- other future entries:
-- +-tcpip
-- | |
-- | +- tcpipIpAddress
-- | +- tcpipGateway
-- | +- tcpipSubnetMask
-- | +- tcpipNegotiation
-- | +- tcpipMAC
-- |
-- +-http
-- | |
-- | +- httpPort
-- | +- httpWriteEnable
-- |
-- +-telnet
-- | |
-- | +- telnetPort
-- |
-- +-canbus
-- | |
-- | +- address
-- | +- address2
-- | +- speed
-- |
-- +-rs232
-- | |
-- | +- ?
-------------------------------------------------------------------------------
-- powersupply
-------------------------------------------------------------------------------
Powersupply ::= SEQUENCE {
--psFirmwareVersion DisplayString,
psSerialNumber DisplayString,
psOperatingTime Integer32,
psDirectAccess OCTET STRING
}
--integrated in system.sysDesc
--psFirmwareVersion OBJECT-TYPE
-- SYNTAX DisplayString
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The firmware version of the power supply main CPU."
-- ::= { powersupply 1 }
psSerialNumber OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The serial number of the power supply."
::= { powersupply 2 }
psOperatingTime OBJECT-TYPE
SYNTAX Integer32
UNITS "s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The time in seconds for how long the power supply was switched on."
::= { powersupply 3 }
psAuxiliaryNumber OBJECT-TYPE
SYNTAX Integer32 (0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of auxiliary channels of the power supply."
::= { powersupply 4 }
psAuxiliaryTable OBJECT-TYPE
SYNTAX SEQUENCE OF PsAuxiliarytEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of psAuxiliary entries."
::= { powersupply 5 }
psDirectAccess OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Direct data transfer to the UEP6000 power supply.
A read access returns nothing, a write access returns the
response of the power supply.
"
::= { powersupply 1024 }
------------------------------------------------------------------------------
psAuxiliaryEntry OBJECT-TYPE
SYNTAX PsAuxiliaryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table row"
INDEX { psAuxiliaryIndex }
::= { psAuxiliaryTable 1 }
OutputEntry ::= SEQUENCE {
psAuxiliaryIndex INTEGER,
psAuxiliaryMeasurementVoltage Float,
psAuxiliaryMeasurementCurrent Float
}
psAuxiliaryIndex OBJECT-TYPE
SYNTAX INTEGER {
u0(1),u1(2),u2(3),u3(4),u4(5),u5(6),u6(7),u7(8)}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each power supply auxiliary channel. Its value
ranges between 1 and total number of output channels.
SMI index starts at 1, so index 1 corresponds to U0."
::= { psAuxiliaryEntry 1 }
psAuxiliaryMeasurementVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured power supply auxiliary output voltage."
::= { psAuxiliaryEntry 3 }
psAuxiliaryMeasurementCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured power supply auxiliary output current."
::= { psAuxiliaryEntry 4 }
-------------------------------------------------------------------------------
-- fantray
-------------------------------------------------------------------------------
Fantray ::= SEQUENCE {
-- fanFirmwareVersion DisplayString,
fanSerialNumber DisplayString,
fanOperatingTime Integer32,
fanAirTemperature INTEGER,
fanSwitchOffDelay INTEGER,
fanNominalSpeed INTEGER,
fanMaxSpeed INTEGER,
fanMinSpeed INTEGER,
fanNumberOfFans INTEGER,
fanConfigMaxSpeed Integer32,
fanConfigMinSpeed Integer32,
fanSpeedTable FanSpeedEntry
}
--integrated in system.sysDesc
--fanFirmwareVersion OBJECT-TYPE
-- SYNTAX DisplayString
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The firmware version of the fan tray CPU."
-- ::= { fantray 1 }
fanSerialNumber OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..14))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The serial number of the fan tray."
::= { fantray 2 }
fanOperatingTime OBJECT-TYPE
SYNTAX Integer32
UNITS "s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The time in seconds for how long the fan tray was switched on."
::= { fantray 3 }
fanAirTemperature OBJECT-TYPE
SYNTAX Integer32
UNITS "deg C"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The temperature of the fan tray inlet air."
::= { fantray 4 }
fanSwitchOffDelay OBJECT-TYPE
SYNTAX Integer32 (0 .. 900)
UNITS "s"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum time in seconds for which the fans will continue running
after the power supply has been switched off. This feature is used
to cool down the electronics after switching off.
"
::= { fantray 5 }
fanNominalSpeed OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0) , (1200..3600) }
-- SYNTAX Integer32 (0..3600)
SYNTAX Integer32
UNITS "RPM"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The nominal fan rotation speed (RPM, Revolutions Per Minute)
Value 0 does switch off the fans (only allowed if at least
one rack temperature sensor is present).
Values 1..1199 are not allowed"
::= { fantray 6 }
fanNumberOfFans OBJECT-TYPE
SYNTAX Integer32 ( 0..12 )
UNITS "Fans"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The number of installed fans"
::= { fantray 7 }
fanSpeedTable OBJECT-TYPE
SYNTAX SEQUENCE OF FanSpeedEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of fanSpeedEntries."
::= { fantray 8 }
fanSpeedEntry OBJECT-TYPE
SYNTAX FanSpeedEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table row"
INDEX { fanNumber }
::= { fanSpeedTable 1 }
FanSpeedEntry ::= SEQUENCE {
fanNumber
INTEGER,
fanSpeed
INTEGER
}
fanNumber OBJECT-TYPE
SYNTAX Integer32 ( 1..12 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each fan."
::= { fanSpeedEntry 1 }
fanSpeed OBJECT-TYPE
SYNTAX Integer32
UNITS "RPM"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured fan rotation speed (RPM, Revolutions Per Minute)"
::= { fanSpeedEntry 2 }
fanMaxSpeed OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0) , (1200..5000) }
-- SYNTAX Integer32 (2900..4000)
SYNTAX INTEGER
UNITS "RPM"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The highest allowed rotationspeed of fan."
::= { fantray 9 }
fanMinSpeed OBJECT-TYPE
-- CHECK SYNTAX INTEGER { (0) , (1000..3600) }
-- SYNTAX Integer32 (1000..1400)
SYNTAX INTEGER
UNITS "RPM"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lowest allowed Rotationspeed of fan."
::= { fantray 10 }
fanConfigMaxSpeed OBJECT-TYPE
SYNTAX Integer32
UNITS "RPM"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Hardwarelimits. Can only set by WIENER."
::= { fantray 11 }
fanConfigMinSpeed OBJECT-TYPE
SYNTAX Integer32
UNITS "RPM"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Hardwarelimits Can only set by WIENER."
::= { fantray 12 }
-------------------------------------------------------------------------------
-- rack
-------------------------------------------------------------------------------
-- this is reserved for futer items (BIN serial number, plug&play, ...)
-- ###################
-------------------------------------------------------------------------------
-- signal
-------------------------------------------------------------------------------
Signal ::= SEQUENCE {
numberOfAnalogInputs Integer32,
analogInputTable AnalogInputEntry,
-- numberOfAnalogOutputs Integer32,
digitalInput BITS,
digitalOutput BITS
}
numberOfAnalogInputs OBJECT-TYPE
SYNTAX Integer32 (0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of additional analog inputs of the crate."
::= { signal 1 }
analogInputTable OBJECT-TYPE
SYNTAX SEQUENCE OF AnalogInputEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A (conceptual table) of analog input data."
::= { signal 2 }
analogInputEntry OBJECT-TYPE
SYNTAX AnalogInputEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) of the analogInputTable."
INDEX { analogInputIndex }
::= { analogInputTable 1 }
AnalogInputEntry ::= SEQUENCE {
analogInputIndex INTEGER,
analogMeasurementVoltage Float
}
analogInputIndex OBJECT-TYPE
SYNTAX Integer32 (1..8)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique number for each analog input of the crate"
::= { analogInputEntry 1 }
analogMeasurementVoltage OBJECT-TYPE
SYNTAX Float
UNITS "V"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured voltage of the analog input."
::= { analogInputEntry 2 }
analogMeasurementCurrent OBJECT-TYPE
SYNTAX Float
UNITS "A"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured current of the analog input."
::= { analogInputEntry 3 }
digitalInput OBJECT-TYPE
SYNTAX BITS {
d0(0) ,
d1(1) ,
d2(2) ,
d3(3) ,
d4(4) ,
d5(5) ,
d6(6) ,
d7(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the digital inputs."
::= { signal 5 }
digitalOutput OBJECT-TYPE
SYNTAX BITS {
d0(0) ,
d1(1) ,
d2(2) ,
d3(3) ,
d4(4) ,
d5(5) ,
d6(6) ,
d7(7)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of the digital outputs. Example set the outputs (d0 and d1) by:
snmpset .... 192.168.x.x b d0,d1
Attention: only Bits from 0..7 allowed! On the other hand, the outputs will be cleared!"
::= { signal 6 }
-- ###################
-------------------------------------------------------------------------------
END