| 10,8 → 10,9 |
|---|
| #include <formatio.h> |
| static int p1; |
| |
| // ./pts -a 0x1000000 -v 1 -w 2 turn LED ON |
| // ./pts -a 0x1000000 -v 1 -w 1 turn LED OFF |
| // sudo ./pts -a 0x1000000 -v 1 -w 2 turn LED ON |
| // sudo ./pts -a 0x1000000 -v 1 -w 1 turn LED OFF |
| // sudo ./ptsvmusb -a 0x02501000 -v 2 -i a.bit -b 2 |
| #include <stdlib.h> |
| #include <stdio.h> |
| |
| 19,18 → 20,13 |
|---|
| |
| #include <string.h> |
| |
| #include "vme.h" |
| |
| #ifndef CAEN_V1718 |
| //typedef unsigned long uint32_t; |
| #endif |
| /* |
| void Delay(double t){ |
| usleep(t*1e6); |
| } |
| */ |
| |
| |
| |
| |
| |
| int verbose; |
| uint32_t ptaddr=0; |
| char str[255]; |
| 37,13 → 33,13 |
|---|
| |
| int Pts_write(uint32_t addr, uint32_t data ){ |
| int i; |
| VME_A32D32_W(ptaddr+addr,&data); |
| VME_A32D32_W(ptaddr+addr,data); |
| return 0; |
| } |
| |
| int Pts_Mwrite(uint32_t addr, uint32_t data ){ |
| int i; |
| VME_A32D32_MW(ptaddr+addr,&data); |
| VME_MW(VME_A32, VME_D32, ptaddr+addr,data); |
| return 0; |
| } |
| |
| 106,8 → 102,6 |
|---|
| (c == 0xff) ? dummyword++ : (dummyword=0); |
| } while( dummyword < 4 ); |
| |
| // const long byte_per_dot = BYTE_PER_DOT; |
| // unsigned long nchar = 0; |
| if( mode == SLAVESERIAL_MODE ) { |
| if(verbose) SetCtrlVal(p1,P1_RESPONSE,"slave serial mode"); |
| Pts_write( ADR_MODE, mode ); |
| 125,7 → 119,10 |
|---|
| if( verbose ) SetCtrlVal(p1,P1_RESPONSE,"select map mode\n"); |
| Pts_write( ADR_MODE, SELECTMAP_MODE ); |
| Pts_erase( verbose ); |
| for( j=0; j<4; j++ ) Pts_write( ADR_CFG, 0xff ); |
| VME_MWRST(); |
| for( j=0; j<4; j++ ) Pts_Mwrite( ADR_CFG, 0xff ); |
| VME_MWEXEC(); |
| |
| VME_MWRST(); |
| while( (c=getc(fp))!=EOF ){ |
| int cc = 0; |
| 227,7 → 224,7 |
|---|
| if ((p1 = LoadPanel (0, "PtsModule_CVI.uir", P1)) < 0) |
| return -1; |
| DisplayPanel (p1); |
| VME_START(NULL); |
| |
| GetCtrlVal(p1,P1_VERBOSE,&verbose); |
| GetCtrlVal(p1,P1_ADDRESS,saddr); |
| ptaddr = strtoul (saddr,NULL,0); |
| 271,8 → 268,11 |
|---|
| case EVENT_COMMIT: |
| GetCtrlVal(p1,P1_FIRMWARE,filename); |
| GetCtrlVal(p1,P1_MODE,&mode); |
| |
| Pts_configure_bit( filename, mode, verbose ); |
| if(VME_CONNECTED() >=0 ) { |
| Pts_configure_bit( filename, mode, verbose ); |
| } else { |
| MessagePopup ("Warning", "Connect VME!!"); |
| } |
| break; |
| } |
| return 0; |
| 471,3 → 471,30 |
|---|
| } |
| return 0; |
| } |
| |
| int CVICALLBACK Connect (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) |
| { |
| int interface = 0; |
| switch (event) |
| { |
| |
| case EVENT_COMMIT: |
| GetCtrlVal (p1, P1_VMEINTERFACE, &interface); |
| VME_START(interface); |
| break; |
| } |
| return 0; |
| } |
| |
| int CVICALLBACK Disconnect (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) |
| { |
| switch (event) |
| { |
| case EVENT_COMMIT: |
| VME_STOP(); |
| break; |
| } |
| return 0; |
| } |