| /cvi/apps/TempCtrl/Arduino_UNO/Arduino_UNO.ino |
|---|
| 0,0 → 1,86 |
| #include <SPI.h> |
| #include <Adafruit_MAX31865.h> |
| #define RREF 430.0 |
| #define RNOMINAL 100.0 |
| Adafruit_MAX31865 max = Adafruit_MAX31865(10, 11, 12, 13); |
| int pinOut1 = 2; |
| int pinOut2 = 4; |
| int state1; |
| int state2; |
| void setup() { |
| pinMode(pinOut1,OUTPUT); |
| pinMode(pinOut2,OUTPUT); |
| digitalWrite(pinOut1, HIGH); |
| digitalWrite(pinOut2, HIGH); |
| Serial.begin(115200); |
| //Serial.println("Temperature"); |
| max.begin(MAX31865_4WIRE); |
| } |
| void loop() { |
| char incomingByte; |
| if (Serial.available() > 0) { |
| // read the incoming byte: |
| incomingByte = Serial.read(); |
| // say what you got: |
| if (incomingByte == 0){ |
| digitalWrite(pinOut1, HIGH); |
| digitalWrite(pinOut2, HIGH); |
| //Serial.println("low"); |
| } |
| else { |
| digitalWrite(pinOut1, LOW); |
| digitalWrite(pinOut2, LOW); |
| //Serial.println("High"); |
| } |
| } |
| uint16_t rtd = max.readRTD(); |
| float t = max.temperature(RNOMINAL, RREF); |
| state1 = digitalRead(pinOut1); |
| state2 = digitalRead(pinOut2); |
| /* |
| Serial.print("RTD value: "); Serial.println(rtd); |
| float ratio = rtd; |
| ratio /= 32768; |
| Serial.print("Ratio = "); Serial.println(ratio,8); |
| Serial.print("Resistance = "); Serial.println(RREF*ratio,8); |
| Serial.print("Temperature = "); Serial.println(max.temperature(RNOMINAL, RREF)); |
| // Preveri in vrne vrednost napak |
| uint8_t fault = max.readFault(); |
| if(fault) { |
| Serial.print("Fault 0x"); Serial.println(fault, HEX); |
| if (fault & MAX31865_FAULT_HIGHTHRESH) { |
| Serial.println("RTD High Threshold"); |
| } |
| if (fault & MAX31865_FAULT_LOWTHRESH) { |
| Serial.println("RTD Low Threshold"); |
| } |
| if (fault & MAX31865_FAULT_REFINHIGH) { |
| Serial.println("REFIN- < 0.85 x Bias - FORCE- open"); |
| } |
| if (fault & MAX31865_FAULT_RTDINLOW) { |
| Serial.println("RTDIN- < 0.85 x Bias - FORCE- open"); |
| } |
| if (fault & MAX31865_FAULT_OVUV) { |
| Serial.println("Under/over voltage"); |
| } |
| max.clearFault(); |
| } |
| */ |
| Serial.print(t); |
| Serial.print(" "); |
| Serial.print(state1); |
| Serial.print(" "); |
| Serial.println(state2); |
| //Serial.println(); |
| delay(1000); |
| } |
| /cvi/apps/TempCtrl/TempCtrl.c |
|---|
| 73,8 → 73,6 |
| GetCtrlVal(pa,PA_CHANNEL, &ch); |
| iRet = TMI_TimeOut(TMI_DeviceId, 1); |
| iRet = TMI_Refresh(TMI_DeviceId); |
| iRet = TMI_MoniDataQ(TMI_DeviceId, ch+1, &Voltage, &Current, &cv_cc); |
| SetCtrlVal(panel, PA_VMON, Voltage); |
| 97,10 → 95,9 |
| GetCtrlVal(pa,PA_CHANNEL, &ch); |
| GetCtrlVal(pa,PA_PRESET, &preset); |
| TMI_VoltageQ(TMI_DeviceId, ch+1, preset, &Voltage); |
| TMI_CurrentQ(TMI_DeviceId, ch+1, preset, &Current); |
| SetCtrlVal(pa, PA_VSET, Voltage); |
| SetCtrlVal(pa, PA_ISET, Current); |
| 109,6 → 106,11 |
| return 0; |
| } |
| int SetCooling(char onoff){ |
| int nb=0; |
| nb = ComWrt (COM_PORT, &onoff, 1); |
| return nb; |
| } |
| #define tcpChk(f) if ((g_TCPError=(f)) < 0) {ReportTCPError(); return -1; } |
| 174,10 → 176,10 |
| printf("Received %s\n", receiveBuf); |
| int cmd=0; |
| float arg; |
| sscanf("%d%f",&cmd,&arg); |
| sscanf(receiveBuf,"%d%f",&cmd,&arg); |
| switch (cmd){ |
| case 1: |
| SetCtrlVal(ps.PA_TSET,arg); |
| SetCtrlVal(pa,PA_TSET,arg); |
| break; |
| default: |
| break; |
| 285,7 → 287,19 |
| return 0; |
| } |
| int CVICALLBACK SwitchCoolingOnOffCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| int onoff=0; |
| switch (event) { |
| case EVENT_COMMIT: |
| GetCtrlVal(pa,control,&onoff); |
| SetCooling(onoff); |
| break; |
| } |
| return 0; |
| } |
| int CVICALLBACK SwitchOnOffCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| 313,8 → 327,13 |
| int debug1; |
| GetCtrlVal(pa,PA_DEBUG_1, &debug1); |
| //printf("%f#%s#", temp, read_data); |
| // temp1 , temp2 , temp3 , temp4 , temp humidity sens, rel.humidity |
| if (bytes_read >0) { |
| SetCtrlVal(pa,PA_ARDUINO, read_data); |
| } |
| sscanf(read_data,"%lf %lf %lf %lf %lf %lf",&f[0],&f[1],&f[2],&f[3],&f[4],&f[5]); |
| double humidity = f[5]; |
| double htemp = f[4]; |
| // printf("%lf %lf %lf %lf %lf %lf",f[0],f[1],f[2],f[3],f[4],f[5]); |
| int RS232Error = ReturnRS232Err (); |
| if (ReturnRS232Err ()) { |
| 338,7 → 357,7 |
| double tdiff = temp - tset; |
| double retpid = UpdatePID(&pid, tdiff, temp); |
| const double troom = 20; |
| const double troom = htemp; |
| double Pheat= 0.2 * (temp - troom); |
| double Ptec = retpid - Pheat*2; |
| vset = (polar*Ptec>0) ? sqrt(fabs(Ptec)) : 0; |
| 362,7 → 381,7 |
| PlotStripChart (pa, PA_GRAPH_VMON, pgraph, 3, 0, 0, VAL_DOUBLE); |
| PlotStripChart (pa, PA_GRAPH_3, &humidity, 1, 0, 0, VAL_DOUBLE); |
| SetCtrlVal(pa,PA_TMON,temp); |
| SetCtrlVal(pa,PA_HTMON,htemp); |
| SetCtrlVal(pa,PA_HUMIDITY,humidity); |
| char transmitBuf[512]= {0}; |
| /cvi/apps/TempCtrl/TempCtrl.h |
|---|
| 19,24 → 19,27 |
| #define PA_START 4 /* control type: command, callback function: StartCB */ |
| #define PA_TSET 5 /* control type: numeric, callback function: (none) */ |
| #define PA_HUMIDITY 6 /* control type: numeric, callback function: (none) */ |
| #define PA_TMON 7 /* control type: numeric, callback function: (none) */ |
| #define PA_DEBUG_1 8 /* control type: radioButton, callback function: (none) */ |
| #define PA_LOG 9 /* control type: radioButton, callback function: (none) */ |
| #define PA_GRAPH_VMON 10 /* control type: strip, callback function: (none) */ |
| #define PA_GRAPH_3 11 /* control type: strip, callback function: (none) */ |
| #define PA_GRAPH 12 /* control type: strip, callback function: (none) */ |
| #define PA_FNAME 13 /* control type: string, callback function: (none) */ |
| #define PA_ONOFF 14 /* control type: binary, callback function: SwitchOnOffCB */ |
| #define PA_CHANNEL 15 /* control type: numeric, callback function: SelectChannelCB */ |
| #define PA_IMAX 16 /* control type: numeric, callback function: (none) */ |
| #define PA_VMAX 17 /* control type: numeric, callback function: (none) */ |
| #define PA_VSET 18 /* control type: numeric, callback function: (none) */ |
| #define PA_VMON 19 /* control type: numeric, callback function: (none) */ |
| #define PA_ISET 20 /* control type: numeric, callback function: (none) */ |
| #define PA_POLAR 21 /* control type: ring, callback function: (none) */ |
| #define PA_IMON 22 /* control type: numeric, callback function: (none) */ |
| #define PA_CVCC 23 /* control type: LED, callback function: (none) */ |
| #define PA_PRESET 24 /* control type: numeric, callback function: SetPresetCB */ |
| #define PA_HTMON 7 /* control type: numeric, callback function: (none) */ |
| #define PA_TMON 8 /* control type: numeric, callback function: (none) */ |
| #define PA_DEBUG_1 9 /* control type: radioButton, callback function: (none) */ |
| #define PA_LOG 10 /* control type: radioButton, callback function: (none) */ |
| #define PA_GRAPH_VMON 11 /* control type: strip, callback function: (none) */ |
| #define PA_GRAPH_3 12 /* control type: strip, callback function: (none) */ |
| #define PA_GRAPH 13 /* control type: strip, callback function: (none) */ |
| #define PA_FNAME 14 /* control type: string, callback function: (none) */ |
| #define PA_ONOFF 15 /* control type: binary, callback function: SwitchOnOffCB */ |
| #define PA_CHANNEL 16 /* control type: numeric, callback function: SelectChannelCB */ |
| #define PA_IMAX 17 /* control type: numeric, callback function: (none) */ |
| #define PA_VMAX 18 /* control type: numeric, callback function: (none) */ |
| #define PA_VSET 19 /* control type: numeric, callback function: (none) */ |
| #define PA_VMON 20 /* control type: numeric, callback function: (none) */ |
| #define PA_ISET 21 /* control type: numeric, callback function: (none) */ |
| #define PA_POLAR 22 /* control type: ring, callback function: (none) */ |
| #define PA_IMON 23 /* control type: numeric, callback function: (none) */ |
| #define PA_CVCC 24 /* control type: LED, callback function: (none) */ |
| #define PA_PRESET 25 /* control type: numeric, callback function: SetPresetCB */ |
| #define PA_FAN 26 /* control type: binary, callback function: SwitchCoolingOnOffCB */ |
| #define PA_ARDUINO 27 /* control type: string, callback function: (none) */ |
| /* Control Arrays: */ |
| 56,6 → 59,7 |
| int CVICALLBACK SetPresetCB(int panel, int control, int event, void *callbackData, int eventData1, int eventData2); |
| int CVICALLBACK StartCB(int panel, int control, int event, void *callbackData, int eventData1, int eventData2); |
| int CVICALLBACK StopCB(int panel, int control, int event, void *callbackData, int eventData1, int eventData2); |
| int CVICALLBACK SwitchCoolingOnOffCB(int panel, int control, int event, void *callbackData, int eventData1, int eventData2); |
| int CVICALLBACK SwitchOnOffCB(int panel, int control, int event, void *callbackData, int eventData1, int eventData2); |
| /cvi/apps/TempCtrl/TempCtrl.uir |
|---|
| Cannot display: file marked as a binary type. |
| svn:mime-type = application/octet-stream |
| /cvi/apps/TempCtrl/TempCtrl_K2231A.c |
|---|
| 0,0 → 1,484 |
| #include "K6517-ctrl.h" |
| #include <tcpsupp.h> |
| #include <rs232.h> |
| #include <utility.h> |
| #include <userint.h> |
| #include <ansi_c.h> |
| #include "K2231A.h" |
| #include "TempCtrl.h" |
| FILE *gFp; |
| #define RSTREG(a,x) (a&=(~(x))) |
| #define SETREG(a,x) (a|=x) |
| int gMask=0xF; |
| static int pa; |
| #define TEXT_LENGTH 2000 |
| char read_data[TEXT_LENGTH]; |
| int read_term_index; |
| int read_term; |
| int read_cnt; |
| int bytes_read; |
| #define COM_PORT 11 |
| typedef struct { |
| double dState; // Last temperature input |
| double iState; // Integrator state |
| double iMax, iMin; // Maximum and minimum allowable integrator state |
| double iGain, // integral gain |
| pGain, // proportional gain |
| dGain; // derivative gain |
| } SPid; |
| SPid pid; |
| double UpdatePID(SPid *pid, double error, double temperature) { |
| double pTerm, dTerm, iTerm; |
| pTerm = pid->pGain * error; |
| // calculate the proportional term |
| // calculate the integral state with appropriate limiting |
| pid->iState += error; |
| if (pid->iState > pid->iMax) pid->iState = pid->iMax; |
| else if (pid->iState < pid->iMin) pid->iState = pid->iMin; |
| //if (debug ) |
| iTerm = pid->iGain * pid->iState; // calculate the integral term |
| dTerm = pid->dGain * (temperature - pid->dState); |
| pid->dState = temperature; |
| return pTerm + iTerm - dTerm; |
| } |
| void SetDimming(int state) { |
| SetCtrlAttribute (pa, PA_START, ATTR_DIMMED, state); |
| SetCtrlAttribute (pa, PA_EXIT, ATTR_DIMMED, state); |
| SetCtrlAttribute (pa, PA_STOP, ATTR_DIMMED, !state); |
| } |
| int CVICALLBACK ReadVoltageCurrentCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| int iRet; |
| char ch=0; |
| double Voltage; |
| double Current; |
| char cv_cc; |
| switch (event) { |
| case EVENT_COMMIT: |
| GetCtrlVal(pa,PA_CHANNEL, &ch); |
| char cmd[0xFF]; |
| K2231A_SelectChannel(ch+1); |
| cv_cc = K2231A_GetOperationMode(); |
| Voltage =K2231A_GetVoltageMonitor(); |
| Current =K2231A_GetCurrentMonitor(); |
| SetCtrlVal(panel, PA_VMON, Voltage); |
| SetCtrlVal(panel, PA_IMON, Current); |
| SetCtrlVal(panel, PA_CVCC, cv_cc); |
| break; |
| } |
| return 0; |
| } |
| int CVICALLBACK SelectChannelCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| unsigned char state, preset; |
| double Voltage, Current; |
| unsigned char ch; |
| switch (event) { |
| case EVENT_COMMIT: |
| GetCtrlVal(pa,PA_CHANNEL, &ch); |
| K2231A_SelectChannel(ch+1); |
| Voltage =K2231A_GetSetVoltage(); |
| Current =K2231A_GetSetCurrent(); |
| SetCtrlVal(pa, PA_VSET, Voltage); |
| SetCtrlVal(pa, PA_ISET, Current); |
| break; |
| } |
| return 0; |
| } |
| int SetCooling(char onoff){ |
| int nb=0; |
| nb = ComWrt (COM_PORT, &onoff, 1); |
| return nb; |
| } |
| #define tcpChk(f) if ((g_TCPError=(f)) < 0) {ReportTCPError(); return -1; } |
| /*---------------------------------------------------------------------------*/ |
| /* Module-globals */ |
| /*---------------------------------------------------------------------------*/ |
| static unsigned int g_hconversation; |
| static int g_TCPError = 0; |
| /*---------------------------------------------------------------------------*/ |
| /* Internal function prototypes */ |
| /*---------------------------------------------------------------------------*/ |
| /*---------------------------------------------------------------------------*/ |
| /* Report TCP Errors if any */ |
| /*---------------------------------------------------------------------------*/ |
| static void ReportTCPError (void) { |
| if (g_TCPError < 0) { |
| char messageBuffer[1024]; |
| sprintf(messageBuffer, |
| "TCP library error message: %s\nSystem error message: %s", |
| GetTCPErrorString (g_TCPError), GetTCPSystemErrorString()); |
| MessagePopup ("Error", messageBuffer); |
| } |
| } |
| int CVICALLBACK ServerTCPCB (unsigned handle, int event, int error, |
| void *callbackData) { |
| char receiveBuf[256] = {0}; |
| ssize_t dataSize = sizeof (receiveBuf) - 1; |
| char addrBuf[31]; |
| switch (event) { |
| case TCP_CONNECT: |
| if (g_hconversation) { |
| /* We already have one client, don't accept another... */ |
| tcpChk (GetTCPPeerAddr (handle, addrBuf, 31)); |
| sprintf (receiveBuf, "-- Refusing conection request from " |
| "%s --\n", addrBuf); |
| printf("%s\n", receiveBuf); |
| tcpChk (DisconnectTCPClient (handle)); |
| } else { |
| /* Handle this new client connection */ |
| g_hconversation = handle; |
| tcpChk (GetTCPPeerAddr (g_hconversation, addrBuf, 31)); |
| printf("%s\n", addrBuf); |
| tcpChk (GetTCPPeerName (g_hconversation, receiveBuf, 256)); |
| printf("%s\n", receiveBuf); |
| sprintf (receiveBuf, "-- New connection from %s --\n", |
| addrBuf); |
| printf("%s\n", receiveBuf); |
| /* Set the disconect mode so we do not need to terminate */ |
| /* connections ourselves. */ |
| tcpChk (SetTCPDisconnectMode (g_hconversation, TCP_DISCONNECT_AUTO)); |
| } |
| break; |
| case TCP_DATAREADY: |
| if ((dataSize = ServerTCPRead (g_hconversation, receiveBuf, dataSize, 1000)) < 0) { |
| printf("Receive Error\n"); |
| } else { |
| receiveBuf[dataSize] = '\0'; |
| printf("Received %s\n", receiveBuf); |
| int cmd=0; |
| float arg; |
| sscanf(receiveBuf,"%d%f",&cmd,&arg); |
| switch (cmd){ |
| case 1: |
| SetCtrlVal(pa,PA_TSET,arg); |
| break; |
| default: |
| break; |
| } |
| } |
| break; |
| case TCP_DISCONNECT: |
| if (handle == g_hconversation) { |
| /* The client we were talking to has disconnected... */ |
| g_hconversation = 0; |
| printf("-- Client disconnected --\n"); |
| /* Note that we do not need to do any more because we set the*/ |
| /* disconnect mode to AUTO. */ |
| } |
| break; |
| } |
| return 0; |
| } |
| int main (int argc, char *argv[]) { |
| int DeviceId=0; |
| unsigned char ch; |
| unsigned char MainOutput, preset=1; |
| double Voltage, Current, tinterval; |
| char str[0xFF]; |
| if (InitCVIRTE (0, argv, 0) == 0) |
| return -1; /* out of memory */ |
| SetStdioPort (CVI_STDIO_WINDOW); |
| pid.iGain= 0.1; |
| pid.dGain= 2; |
| pid.pGain = 5; |
| pid.iMax =100; |
| pid.iMin =-100 ; |
| pid.iState=0; |
| pid.dState=0; |
| if ((pa = LoadPanel (0, "TempCtrl.uir", PA)) < 0) |
| return -1; |
| DisableBreakOnLibraryErrors(); |
| K2231A_SetPort(6); |
| K2231A_SetDebug(1); |
| if (K2231A_Open()== 0) MessagePopup("Error","Cannot open USB device"); |
| K2231A_Test(); |
| MainOutput = K2231A_GetSwitch(); |
| SetCtrlVal(pa, PA_ONOFF, MainOutput); |
| SetCtrlVal(pa, PA_PRESET, preset); |
| int debug1; |
| GetCtrlVal(pa,PA_DEBUG_1, &debug1); |
| K2231A_SetDebug(1); |
| SetCtrlVal(pa,PA_CHANNEL, 0); |
| /* |
| GetCtrlVal(pa, P1_TINTERVAL, &tinterval); |
| SetCtrlAttribute (pa, P1_TIMER, ATTR_INTERVAL, tinterval); |
| */ |
| SetWaitCursor (1); |
| int portNum = 10000; |
| int registered = 0; |
| char tempBuf[256] = {0}; |
| if (RegisterTCPServer (portNum, ServerTCPCB, 0) < 0) |
| MessagePopup("TCP Server", "Server registration failed!"); |
| else { |
| SetWaitCursor (0); |
| registered = 1; |
| /* We are successfully connected -- gather info */ |
| if (GetTCPHostAddr (tempBuf, 256) >= 0) printf("%s\n" ,tempBuf); |
| if (GetTCPHostName (tempBuf, 256) >= 0) printf("%s\n" ,tempBuf); |
| } |
| SelectChannelCB (pa, PA_CHANNEL, EVENT_COMMIT, NULL, 0,0); |
| ReadVoltageCurrentCB (pa, PA_CHANNEL, EVENT_COMMIT, NULL, 0,0); |
| DisplayPanel (pa); |
| SetDimming(0); |
| RunUserInterface (); |
| CloseCom(COM_PORT); |
| if (registered) |
| UnregisterTCPServer (portNum); |
| DiscardPanel (pa); |
| K2231A_Close(); |
| if (gFp) fclose(gFp); |
| return 0; |
| } |
| int CVICALLBACK ExitCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| switch (event) { |
| case EVENT_COMMIT: |
| QuitUserInterface (0); |
| break; |
| } |
| return 0; |
| } |
| int CVICALLBACK SwitchCoolingOnOffCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| int onoff=0; |
| switch (event) { |
| case EVENT_COMMIT: |
| GetCtrlVal(pa,control,&onoff); |
| SetCooling(onoff); |
| break; |
| } |
| return 0; |
| } |
| int CVICALLBACK SwitchOnOffCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| unsigned char state; |
| switch (event) { |
| case EVENT_COMMIT: |
| GetCtrlVal(panel, control, &state); |
| K2231A_SetSwitch(state); |
| break; |
| } |
| return 0; |
| } |
| /* Callback Function */ |
| void ComCallback(int portNumber, int eventMask, void *callbackdata) { |
| static double told=0; |
| if (eventMask & LWRS_RXFLAG) { |
| //printf("Received specified character\n"); |
| int strLen = GetInQLen (COM_PORT); |
| bytes_read = ComRd (COM_PORT, read_data, strLen); |
| double temp= atof(read_data); |
| double f[10]; |
| int debug1; |
| GetCtrlVal(pa,PA_DEBUG_1, &debug1); |
| K2231A_SetDebug(debug1); |
| //printf("%f#%s#", temp, read_data); |
| // temp1 , temp2 , temp3 , temp4 , temp humidity sens, rel.humidity |
| if (bytes_read >0) { |
| SetCtrlVal(pa,PA_ARDUINO, read_data); |
| } |
| sscanf(read_data,"%lf %lf %lf %lf %lf %lf",&f[0],&f[1],&f[2],&f[3],&f[4],&f[5]); |
| double humidity = f[5]; |
| double htemp = f[4]; |
| // printf("%lf %lf %lf %lf %lf %lf",f[0],f[1],f[2],f[3],f[4],f[5]); |
| int RS232Error = ReturnRS232Err (); |
| if (ReturnRS232Err ()) { |
| sprintf(read_data,"#%s\n", GetRS232ErrorString(RS232Error)); |
| MessagePopup("RS232Err",read_data); |
| } else { |
| int polar; |
| ProcessSystemEvents (); |
| SelectChannelCB (pa, PA_CHANNEL, EVENT_COMMIT, NULL, 0,0); |
| ProcessSystemEvents (); |
| ReadVoltageCurrentCB (pa, PA_CHANNEL, EVENT_COMMIT, NULL, 0,0); |
| ProcessSystemEvents (); |
| double tset,vmon,imon,vset,iset,vmax; |
| unsigned char ch, preset; |
| GetCtrlVal(pa,PA_TSET,&tset); |
| GetCtrlVal(pa,PA_VMON,&vmon); |
| GetCtrlVal(pa,PA_IMON,&imon); |
| GetCtrlVal(pa,PA_CHANNEL, &ch); |
| //GetCtrlVal(pa,PA_PRESET,&preset); |
| //TMI_Preset(TMI_DeviceId,preset); |
| GetCtrlVal(pa,PA_POLAR,&polar); |
| double tdiff = temp - tset; |
| double retpid = UpdatePID(&pid, tdiff, temp); |
| const double troom = htemp; |
| double Pheat= 0.2 * (temp - troom); |
| double Ptec = retpid - Pheat*2; |
| vset = (polar*Ptec>0) ? sqrt(fabs(Ptec)) : 0; |
| if (debug1) printf("%d PID tmon=%f tset=%f tdiff=%f vmon=%f imom=%f pid=%f Pheat=%f =>vset %f", ch, temp, tset, tdiff, vmon, imon,retpid ,Pheat, vset); |
| GetCtrlVal(pa,PA_VMAX,&vmax); |
| if (vset >vmax) vset=vmax; |
| if (vset <0) vset =0; |
| if (debug1) printf("vset --->%f \n",vset); |
| K2231A_SelectChannel(ch+1); |
| K2231A_SetVoltage(vset); |
| GetCtrlVal(pa,PA_IMAX,&iset); |
| K2231A_SetCurrent(iset); |
| ReadVoltageCurrentCB (pa, PA_CHANNEL, EVENT_COMMIT, NULL, 0,0); |
| PlotStripChart (pa, PA_GRAPH, &temp, 1, 0, 0, VAL_DOUBLE); |
| double pgraph[3]= {vmon,imon, 100*(temp-told)}; |
| PlotStripChart (pa, PA_GRAPH_VMON, pgraph, 3, 0, 0, VAL_DOUBLE); |
| PlotStripChart (pa, PA_GRAPH_3, &humidity, 1, 0, 0, VAL_DOUBLE); |
| SetCtrlVal(pa,PA_TMON,temp); |
| SetCtrlVal(pa,PA_HTMON,htemp); |
| SetCtrlVal(pa,PA_HUMIDITY,humidity); |
| char transmitBuf[512]= {0}; |
| sprintf(transmitBuf, "%u %f %f %f %f\n", time(NULL), humidity, temp, tdiff, temp-told); |
| if (g_hconversation) |
| if ( ServerTCPWrite (g_hconversation, transmitBuf, strlen (transmitBuf), 1000) < 0) printf("Transmit Error\n"); |
| int log=0; |
| GetCtrlVal(pa,PA_LOG, &log); |
| if (log) { |
| char fname[0xFF]; |
| GetCtrlVal(pa,PA_FNAME, fname); |
| FILE *fp = fopen (fname,"a"); |
| fprintf(fp,transmitBuf); |
| fclose(fp); |
| } |
| told= temp; |
| } |
| } |
| if (eventMask & LWRS_TXEMPTY) |
| printf("Transmit queue now empty\n"); |
| if (eventMask & LWRS_RECEIVE) { |
| printf("50 or more bytes in input queue\n"); |
| } |
| } |
| int CVICALLBACK StartCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| switch (event) { |
| case EVENT_COMMIT: |
| OpenComConfig (COM_PORT, "", 115200, 0, 8, 1, 512, 512); |
| /* Turn off Hardware handshaking (loopback test will not function with it on) */ |
| SetCTSMode (COM_PORT, LWRS_HWHANDSHAKE_OFF); |
| /* Make sure Serial buffers are empty */ |
| FlushInQ (COM_PORT); |
| FlushOutQ (COM_PORT); |
| int notifyCount = 50; /* Wait for at least 50 bytes in queue. */ |
| int eventChar = 10; /* Wait for LF. */ |
| int eventMask = LWRS_RXFLAG | LWRS_TXEMPTY | LWRS_RECEIVE; |
| InstallComCallback (COM_PORT, eventMask, notifyCount, eventChar, ComCallback, NULL); |
| SetDimming(1); |
| break; |
| } |
| return 0; |
| } |
| int CVICALLBACK StopCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| switch (event) { |
| case EVENT_COMMIT: |
| CloseCom(COM_PORT); |
| SetDimming(0); |
| break; |
| } |
| return 0; |
| } |
| int CVICALLBACK SetPresetCB (int panel, int control, int event, |
| void *callbackData, int eventData1, int eventData2) { |
| switch (event) { |
| case EVENT_COMMIT: { |
| unsigned char preset; |
| double Voltage, Current; |
| GetCtrlVal(panel, control, &preset); |
| K2231A_RecallFromMemory(preset); |
| break; |
| } |
| } |
| return 0; |
| } |
| /cvi/apps/TempCtrl/TempCtrl_K2231A.prj |
|---|
| 0,0 → 1,432 |
| [Project Header] |
| Version = 1302 |
| Pathname = "/c/home/CVI/apps/TempCtrl/TempCtrl_K2231A.prj" |
| CVI Dir = "/c/program files/national instruments/cvi2013" |
| CVI Shared Dir = "/C/Program Files/National Instruments/Shared/CVI" |
| CVI Pub Local Dir = "/C/ProgramData/National Instruments/CVI2013" |
| CVI Pub Global Dir = "/C/ProgramData/National Instruments/CVI" |
| IVI Standard Root Dir = "/C/Program Files/IVI Foundation/IVI" |
| VXIplug&play Framework Dir = "/C/Program Files/IVI Foundation/VISA/winnt" |
| IVI Standard Root 64-bit Dir = "/C/Program Files/IVI Foundation/IVI" |
| VXIplug&play Framework 64-bit Dir = "/C/Program Files/IVI Foundation/VISA/win64" |
| Number of Files = 3 |
| Target Type = "Executable" |
| Flags = 2064 |
| Copied From Locked InstrDrv Directory = False |
| Copied from VXIPNP Directory = False |
| Locked InstrDrv Name = "" |
| Don't Display Deploy InstrDrv Dialog = False |
| [Folders] |
| Include Files Folder Not Added Yet = True |
| Library Files Folder Not Added Yet = True |
| Folder 0 = "Source Files" |
| FolderEx 0 = "Source Files" |
| Folder 1 = "Instrument Files" |
| FolderEx 1 = "Instrument Files" |
| Folder 2 = "User Interface Files" |
| FolderEx 2 = "User Interface Files" |
| [File 0001] |
| File Type = "CSource" |
| Res Id = 1 |
| Path Is Rel = True |
| Path Rel To = "Project" |
| Path Rel Path = "TempCtrl_K2231A.c" |
| Path = "/c/home/CVI/apps/TempCtrl/TempCtrl_K2231A.c" |
| Exclude = False |
| Compile Into Object File = False |
| Project Flags = 0 |
| Folder = "Source Files" |
| Folder Id = 0 |
| [File 0002] |
| File Type = "Function Panel" |
| Res Id = 2 |
| Path Is Rel = True |
| Path Rel To = "Project" |
| Path Rel Path = "../../instr/K2231A/K2231A.fp" |
| Path = "/c/home/CVI/instr/K2231A/K2231A.fp" |
| Exclude = False |
| Project Flags = 0 |
| Folder = "Instrument Files" |
| Folder Id = 1 |
| [File 0003] |
| File Type = "User Interface Resource" |
| Res Id = 3 |
| Path Is Rel = True |
| Path Rel To = "Project" |
| Path Rel Path = "TempCtrl.uir" |
| Path = "/c/home/CVI/apps/TempCtrl/TempCtrl.uir" |
| Exclude = False |
| Project Flags = 0 |
| Folder = "User Interface Files" |
| Folder Id = 2 |
| [Custom Build Configs] |
| Num Custom Build Configs = 0 |
| [Default Build Config Debug] |
| Config Name = "Debug" |
| Is 64-Bit = False |
| Is Release = False |
| Default Calling Convention = "cdecl" |
| Optimization Level = "Optimize for speed (level 2)" |
| Require Prototypes = True |
| Show Warning IDs in Build Output = False |
| Selected Warning Level = "None" |
| Warning List None = "4,9,84,105,106,107,108,109,110,111" |
| Warning List Common = "" |
| Warning List Extended = "" |
| Warning List All = "" |
| Warning Mode = 0 |
| Enable Unreferenced Identifiers Warning = False |
| Enable Pointer Mismatch Warning = False |
| Enable Unreachable Code Warning = False |
| Enable Assignment In Conditional Warning = False |
| Uninitialized Locals Compile Warning = "Aggressive" |
| Require Return Values = True |
| Enable C99 Extensions = False |
| Enable OpenMP Extensions = False |
| Stack Size = 500000 |
| Stack Reserve = 1048576 |
| Stack Commit = 4096 |
| Image Base Address = 4194304 |
| Image Base Address x64 = 4194304 |
| Compiler Defines = "/DWIN32_LEAN_AND_MEAN" |
| Sign = False |
| Sign Store = "" |
| Sign Certificate = "" |
| Sign Timestamp URL = "" |
| Sign URL = "" |
| Manifest Embed = False |
| Icon File Is Rel = False |
| Icon File = "" |
| Application Title = "" |
| Use IVI Subdirectories for Import Libraries = False |
| Use VXIPNP Subdirectories for Import Libraries = False |
| Use Dflt Import Lib Base Name = True |
| Where to Copy DLL = "Do not copy" |
| Custom Directory to Copy DLL Is Rel = False |
| Custom Directory to Copy DLL = "" |
| Generate Source Documentation = "None" |
| Runtime Support = "Full Runtime Support" |
| Runtime Binding = "Shared" |
| Embed Project .UIRs = False |
| Generate Map File = False |
| Embed Timestamp = True |
| Create Console Application = False |
| Using LoadExternalModule = False |
| DLL Exports = "Include File Symbols" |
| Register ActiveX Server = False |
| Numeric File Version = "1,0,0,0" |
| Numeric Prod Version = "1,0,0,0" |
| Comments = "" |
| Comments Ex = "" |
| Company Name = "" |
| Company Name Ex = "%company" |
| File Description = "TempCtrl_K2231A (Debug x86)" |
| File Description Ex = "%application (%rel_dbg %arch)" |
| File Version = "1.0" |
| File Version Ex = "%f1.%f2" |
| Internal Name = "TempCtrl_K2231A" |
| Internal Name Ex = "%basename" |
| Legal Copyright = "Copyright © 2018" |
| Legal Copyright Ex = "Copyright © %company %Y" |
| Legal Trademarks = "" |
| Legal Trademarks Ex = "" |
| Original Filename = "TempCtrl_K2231A.exe" |
| Original Filename Ex = "%filename" |
| Private Build = "" |
| Private Build Ex = "" |
| Product Name = " TempCtrl_K2231A" |
| Product Name Ex = "%company %application" |
| Product Version = "1.0" |
| Product Version Ex = "%p1.%p2" |
| Special Build = "" |
| Special Build Ex = "" |
| Add Type Lib To DLL = False |
| Include Type Lib Help Links = False |
| TLB Help Style = "HLP" |
| Type Lib FP File Is Rel = False |
| Type Lib FP File = "" |
| [Default Build Config Release] |
| Config Name = "Release" |
| Is 64-Bit = False |
| Is Release = True |
| Default Calling Convention = "cdecl" |
| Optimization Level = "Optimize for speed (level 2)" |
| Require Prototypes = True |
| Show Warning IDs in Build Output = False |
| Selected Warning Level = "None" |
| Warning List None = "4,9,84,105,106,107,108,109,110,111" |
| Warning List Common = "" |
| Warning List Extended = "" |
| Warning List All = "" |
| Warning Mode = 0 |
| Enable Unreferenced Identifiers Warning = False |
| Enable Pointer Mismatch Warning = False |
| Enable Unreachable Code Warning = False |
| Enable Assignment In Conditional Warning = False |
| Uninitialized Locals Compile Warning = "Aggressive" |
| Require Return Values = True |
| Enable C99 Extensions = False |
| Enable OpenMP Extensions = False |
| Stack Size = 500000 |
| Stack Reserve = 1048576 |
| Stack Commit = 4096 |
| Image Base Address = 4194304 |
| Image Base Address x64 = 4194304 |
| Compiler Defines = "/DWIN32_LEAN_AND_MEAN /DCAEN_V1718 /DBELLEPTS" |
| Sign = False |
| Sign Store = "" |
| Sign Certificate = "" |
| Sign Timestamp URL = "" |
| Sign URL = "" |
| Manifest Embed = False |
| Icon File Is Rel = False |
| Icon File = "" |
| Application Title = "" |
| Use IVI Subdirectories for Import Libraries = False |
| Use VXIPNP Subdirectories for Import Libraries = False |
| Use Dflt Import Lib Base Name = True |
| Where to Copy DLL = "Do not copy" |
| Custom Directory to Copy DLL Is Rel = False |
| Custom Directory to Copy DLL = "" |
| Generate Source Documentation = "None" |
| Runtime Support = "Full Runtime Support" |
| Runtime Binding = "Shared" |
| Embed Project .UIRs = False |
| Generate Map File = False |
| Embed Timestamp = True |
| Create Console Application = False |
| Using LoadExternalModule = False |
| DLL Exports = "Include File Symbols" |
| Register ActiveX Server = False |
| Add Type Lib To DLL = False |
| Include Type Lib Help Links = False |
| TLB Help Style = "HLP" |
| Type Lib FP File Is Rel = False |
| Type Lib FP File = "" |
| [Default Build Config Debug64] |
| Config Name = "Debug64" |
| Is 64-Bit = True |
| Is Release = False |
| Default Calling Convention = "cdecl" |
| Optimization Level = "Optimize for speed (level 2)" |
| Require Prototypes = True |
| Show Warning IDs in Build Output = False |
| Selected Warning Level = "None" |
| Warning List None = "4,9,84,105,106,107,108,109,110,111" |
| Warning List Common = "" |
| Warning List Extended = "" |
| Warning List All = "" |
| Warning Mode = 0 |
| Enable Unreferenced Identifiers Warning = False |
| Enable Pointer Mismatch Warning = False |
| Enable Unreachable Code Warning = False |
| Enable Assignment In Conditional Warning = False |
| Uninitialized Locals Compile Warning = "Aggressive" |
| Require Return Values = True |
| Enable C99 Extensions = False |
| Enable OpenMP Extensions = False |
| Stack Size = 500000 |
| Stack Reserve = 1048576 |
| Stack Commit = 4096 |
| Image Base Address = 4194304 |
| Image Base Address x64 = 4194304 |
| Compiler Defines = "/DWIN32_LEAN_AND_MEAN /DCAEN_V1718 /DBELLEPTS" |
| Sign = False |
| Sign Store = "" |
| Sign Certificate = "" |
| Sign Timestamp URL = "" |
| Sign URL = "" |
| Manifest Embed = False |
| Icon File Is Rel = False |
| Icon File = "" |
| Application Title = "" |
| Use IVI Subdirectories for Import Libraries = False |
| Use VXIPNP Subdirectories for Import Libraries = False |
| Use Dflt Import Lib Base Name = True |
| Where to Copy DLL = "Do not copy" |
| Custom Directory to Copy DLL Is Rel = False |
| Custom Directory to Copy DLL = "" |
| Generate Source Documentation = "None" |
| Runtime Support = "Full Runtime Support" |
| Runtime Binding = "Shared" |
| Embed Project .UIRs = False |
| Generate Map File = False |
| Embed Timestamp = True |
| Create Console Application = False |
| Using LoadExternalModule = False |
| DLL Exports = "Include File Symbols" |
| Register ActiveX Server = False |
| Add Type Lib To DLL = False |
| Include Type Lib Help Links = False |
| TLB Help Style = "HLP" |
| Type Lib FP File Is Rel = False |
| Type Lib FP File = "" |
| [Default Build Config Release64] |
| Config Name = "Release64" |
| Is 64-Bit = True |
| Is Release = True |
| Default Calling Convention = "cdecl" |
| Optimization Level = "Optimize for speed (level 2)" |
| Require Prototypes = True |
| Show Warning IDs in Build Output = False |
| Selected Warning Level = "None" |
| Warning List None = "4,9,84,105,106,107,108,109,110,111" |
| Warning List Common = "" |
| Warning List Extended = "" |
| Warning List All = "" |
| Warning Mode = 0 |
| Enable Unreferenced Identifiers Warning = False |
| Enable Pointer Mismatch Warning = False |
| Enable Unreachable Code Warning = False |
| Enable Assignment In Conditional Warning = False |
| Uninitialized Locals Compile Warning = "Aggressive" |
| Require Return Values = True |
| Enable C99 Extensions = False |
| Enable OpenMP Extensions = False |
| Stack Size = 500000 |
| Stack Reserve = 1048576 |
| Stack Commit = 4096 |
| Image Base Address = 4194304 |
| Image Base Address x64 = 4194304 |
| Compiler Defines = "/DWIN32_LEAN_AND_MEAN /DCAEN_V1718 /DBELLEPTS" |
| Sign = False |
| Sign Store = "" |
| Sign Certificate = "" |
| Sign Timestamp URL = "" |
| Sign URL = "" |
| Manifest Embed = False |
| Icon File Is Rel = False |
| Icon File = "" |
| Application Title = "" |
| Use IVI Subdirectories for Import Libraries = False |
| Use VXIPNP Subdirectories for Import Libraries = False |
| Use Dflt Import Lib Base Name = True |
| Where to Copy DLL = "Do not copy" |
| Custom Directory to Copy DLL Is Rel = False |
| Custom Directory to Copy DLL = "" |
| Generate Source Documentation = "None" |
| Runtime Support = "Full Runtime Support" |
| Runtime Binding = "Shared" |
| Embed Project .UIRs = False |
| Generate Map File = False |
| Embed Timestamp = True |
| Create Console Application = False |
| Using LoadExternalModule = False |
| DLL Exports = "Include File Symbols" |
| Register ActiveX Server = False |
| Add Type Lib To DLL = False |
| Include Type Lib Help Links = False |
| TLB Help Style = "HLP" |
| Type Lib FP File Is Rel = False |
| Type Lib FP File = "" |
| [Compiler Options] |
| Default Calling Convention = "cdecl" |
| Require Prototypes = True |
| Require Return Values = True |
| Enable Pointer Mismatch Warning = False |
| Enable Unreachable Code Warning = False |
| Enable Unreferenced Identifiers Warning = False |
| Enable Assignment In Conditional Warning = False |
| O Option Compatible With 5.0 = False |
| Enable C99 Extensions = False |
| Uninitialized Locals Compile Warning = "Aggressive" |
| Precompile Prefix Header = False |
| Prefix Header File = "" |
| [Run Options] |
| Stack Size = 500000 |
| Stack Commit = 4096 |
| Image Base Address = 4194304 |
| Image Base Address x64 = 4194304 |
| [Compiler Defines] |
| Compiler Defines = "/DWIN32_LEAN_AND_MEAN /DCAEN_V1718 /DBELLEPTS" |
| [Create Executable] |
| Executable File_Debug Is Rel = True |
| Executable File_Debug Rel To = "Project" |
| Executable File_Debug Rel Path = "TempCtrl_K2231A.exe" |
| Executable File_Debug = "/c/home/CVI/apps/TempCtrl/TempCtrl_K2231A.exe" |
| Executable File_Release Is Rel = True |
| Executable File_Release Rel To = "Project" |
| Executable File_Release Rel Path = "TempCtrl_K2231A.exe" |
| Executable File_Release = "/c/home/CVI/apps/TempCtrl/TempCtrl_K2231A.exe" |
| Executable File_Debug64 Is Rel = True |
| Executable File_Debug64 Rel To = "Project" |
| Executable File_Debug64 Rel Path = "TempCtrl_K2231A.exe" |
| Executable File_Debug64 = "/c/home/CVI/apps/TempCtrl/TempCtrl_K2231A.exe" |
| Executable File_Release64 Is Rel = True |
| Executable File_Release64 Rel To = "Project" |
| Executable File_Release64 Rel Path = "TempCtrl_K2231A.exe" |
| Executable File_Release64 = "/c/home/CVI/apps/TempCtrl/TempCtrl_K2231A.exe" |
| Icon File Is Rel = False |
| Icon File = "" |
| Application Title = "" |
| DLL Exports = "Include File Symbols" |
| Use IVI Subdirectories for Import Libraries = False |
| Use VXIPNP Subdirectories for Import Libraries = False |
| Use Dflt Import Lib Base Name = True |
| Where to Copy DLL = "Do not copy" |
| Custom Directory to Copy DLL Is Rel = False |
| Custom Directory to Copy DLL = "" |
| Generate Source Documentation = "None" |
| Add Type Lib To DLL = False |
| Include Type Lib Help Links = False |
| TLB Help Style = "HLP" |
| Type Lib FP File Is Rel = False |
| Type Lib FP File = "" |
| Type Lib Guid = "" |
| Runtime Support = "Full Runtime Support" |
| Instrument Driver Support Only = False |
| Embed Project .UIRs = False |
| Generate Map File = False |
| [External Compiler Support] |
| UIR Callbacks File Option = 0 |
| Using LoadExternalModule = False |
| Create Project Symbols File = True |
| UIR Callbacks Obj File Is Rel = False |
| UIR Callbacks Obj File = "" |
| Project Symbols H File Is Rel = False |
| Project Symbols H File = "" |
| Project Symbols Obj File Is Rel = False |
| Project Symbols Obj File = "" |
| [ActiveX Server Options] |
| Specification File Is Rel = False |
| Specification File = "" |
| Source File Is Rel = False |
| Source File = "" |
| Include File Is Rel = False |
| Include File = "" |
| IDL File Is Rel = False |
| IDL File = "" |
| Register ActiveX Server = False |
| [Signing Info] |
| Sign = False |
| Sign Debug Build = False |
| Store = "" |
| Certificate = "" |
| Timestamp URL = "" |
| URL = "" |
| [Manifest Info] |
| Embed = False |
| [tpcSection] |
| tpcEnabled = 0 |
| tpcOverrideEnvironment = 0 |
| tpcEnabled x64 = 0 |
| tpcOverrideEnvironment x64 = 0 |